Abstract:A TD-split basal texture with two peaks highly tilted from the normal direction (ND) towards the transverse direction (TD) is usually developed in Mg-Zn-Ca plates and can effectively improve ductility and formability. In the present study, the texture evolution during cold rolling and subsequent annealing of a Mg-2Zn-1Ca plate with initial TD-split texture was investigated, and new insights into the mechanisms of texture evolution were obtained. The results show that a dumbbell-shaped basal texture transformed into an elliptical shape after 41% cold rolling. The random distribution of prismatic planes became preferred with largely parallel to the rolling direction (RD). Crystal plasticity simulations revealed that basal slip was the predominant deformation mode, and inclined basal poles toward the ND. The activation of other non-basal slips would retard this tendency. Prismatic slip with a relative activity of 20% to 30% preserved the pre-existing TD-split texture after a high rolling reduction of 41%. Pyramidal slip prevented the formation of basal fiber and lead to a spreading of basal poles toward the RD mainly at strains over 29%. After full recrystallization, the elliptical TD-split basal texture became a dumbbell-shaped TD-split texture. Grain nucleation was observed at grain boundaries (GBN mechanism), within deformation twins (DTN mechanism), and near precipitates (PSN mechanism). GBN and DTN mainly developed a TD-split basal-texture. Instead of the formation of random orientations as considered previously, PSN produced a TD-split basal-texture, and the basal poles exhibited a much wider distribution with high angle of the peaks off the ND. The grains nucleated by GBN, DTN, and PSN did not exhibit preferred growth, and consequently, the texture hardly changed during subsequent grain growth.

Slip-induced Texture Evolution of Rolled Mg–6Al–3Sn Alloy During Uniaxial Tension along Rolling and Transverse Directions

Slip Behavior and Its Effect on Rolling Texture Development in a Dual-Phase Mg–Li Alloy

Texture Evolution in an Al-Cu-Mg Alloy During Hot Rolling

Unveiling the Rolling Texture Variations of Α-Mg Phases in a Dual-Phase Mg-Li Alloy

Effect of Al addition and rolling reduction on microstructure and texture evolution of Mg–3Sn alloy during high-speed rolling

Strain Path Dependence of Texture and Property Evolutions on Rolled Mg-Li-Al-Zn Alloy Possessed of an Asymmetric Texture

Formation of Unusual Rolling Texture in a Mg-Al-Mn Alloy Sheet by Large-Strain Hot-Rolling

Non-Basal Slip Induced Rare Earth Texture Evolution in Mg-14Gd-0.5Zr (wt.%) Alloy During the Traditional Hot Rolling

Texture Evolution in Rolled Mg-13wt%Li-X Alloy

Insights into the evolution of texture and mechanical properties during warm rolling and annealing of Mg–2Zn-0.5Ca alloy

The Role of Al Content on Deformation Behavior and Related Texture Evolution During Hot Rolling of Mg-Al-Zn Alloys

Rolling texture development in a dual-phase Mg-Li alloy: The role of temperature

Ex-situ EBSD Analysis of Yield Asymmetry, Texture and Twinning Development in Mg–5Li–3Al–2Zn Alloy During Tensile and Compressive Deformation

Texture evolution during multi-pass cold rolling and annealing of Ti-2Al-1.5Mn alloy

Understanding the mechanisms of texture evolution in an Mg-2Zn-1Ca alloy during cold rolling and annealing

Effects of dislocation slip behaviour and second-phase particles on hot rolled texture of an Al-Cu-Mg alloy with a high Cu/Mg ratio

Texture Evolution of Al-Zn-Mg-Cu Aluminum Alloy Plate During Cold Rolling

Texture Evolution of Al-Mg-Li Aeronautical Alloys in In-Situ Tension

Twinning and Mechanical Behavior of an Extruded Mg–6Al–3Sn Alloy with a Dual Basal Texture

Deformation Behavior and Texture Evolution in an Extruded Mg-Li Sheet with Non-Basal Texture During Tensile Deformation

Texture Evolution and Their Effects on the Mechanical Properties of Duplex Mg–Li Alloy