Abstract:The texture evolution, crystal orientation-dependent deformation mechanism and mechanical properties of the Mg-5.5Gd-4.4Y-1.1Zn-0.5Zr (wt%) alloy sheet with bimodal grain structure during hot rolling were investigated in this study. The pre-rolled sheet possesses the texture with c-axis randomly distributed in rolling-transverse plane. During the hot rolling deformation, the initial texture is gradually changed to an uncommon texture with c-axis continuously distributed between transverse direction (TD) and normal direction (ND) of the rolled sheet. The formation of the texture is related to the orientation-dependent deformation mechanism of coarse grains. For the coarse grains with c-axis close to rolling direction (RD), {10-12} twinning was identified to be the dominated deformation mechanism. With the activation of twinning, the c-axis of the matrix is reoriented towards ND. For the coarse grains with c-axis near TD, prism slip and kink deformation were figured out as the dominated deformation modes. In early stage of the hot rolling deformation, the c-axis of the grains remains in TD with the activation of prism slip. Afterwards, kink deformation activates and the c-axis of the grains is rotated away from TD towards ND with different degrees. In addition, the mechanical properties of rolled sheets were examined and the results demonstrate that yield strength and tensile strength are gradually improved by rolling deformation. Nevertheless, the improvement of yield strength in RD is much greater than that in TD and a serious yield strength anisotropy is shown in the rolled sheet. The strong yield strength anisotropy derives from the variation of texture strengthening in the RD and TD due to the formation the texture with c-axis continuously distributed between TD and ND.

Texture Formation under Control of S Phase Characteristic and Tensile Property of Hot-Rolling 2A12 Aluminum Alloy Improved by Brass Texture

Evolution of the Brass Texture in an Al-Cu-Mg Alloy During Hot Rolling

Texture Evolution in an Al-Cu-Mg Alloy During Hot Rolling

Developing Alternative Texture in a 90Cu-10Zn α-Brass Alloy via Route Changes in Accumulative Roll Bonding Process

Shear Texture Gradient in Aa6061 Aluminum Alloy Processed by Accumulative Roll Bonding with High Roll Roughness

Enhanced Brass texture of hot-rolled Al-4Cu-1.6Mg alloy by 0.1% Zr addition

New insight of texture and microstructure evolution, and the connections between with tensile performance in as-annealed Al-Cu-Mg-Zr sheet

Texture Evolution in Hot-Rolled Al–Cu–Mg Sheets Using Orientation Streamline Approach and Texture Index

Effect of S Phase Characteristics on the Formation of Recrystallization Textures of an Al-Cu-Mg Alloy

Study of Texture in 6016 Aluminum Alloy During Processing

Effect of rolling geometry on the mechanical properties, microstructure and recrystallization texture of Al-Mg-Si alloys

Microstructure and Texture Evolution of Cu–Cr–Co–Ti Alloys During the Two-Stage Cryorolling

Microstructure evolution and mechanical properties of Al-Cu-Li alloys with different rolling schedules and subsequent artificial ageing heat treatment

Effect of Accumulative Roll Bonding Process on Textural Evolution and Its Comparison with Normal Rolled AA7005 Aluminum Alloy

Micro-mechanism of Texture Evolution During Isochronal Annealing of As-Annealed Hot Rolled Al-Cu-Mg Sheet

Texture Evolution of Hot Rolled Al–Cu–Mg–Zr Alloy During Annealing

Insights into the evolution of texture and mechanical properties during warm rolling and annealing of Mg–2Zn-0.5Ca alloy

Strength and structure variation of 2195 Al-Li alloy caused by different deformation processes of hot extrusion and cold-rolling

Texture Evolution, Deformation Mechanism and Mechanical Properties of the Hot Rolled Mg-Gd-Y-Zn-Zr Alloy Containing LPSO Phase

Texture Evolution of Al-Mg-Li Aeronautical Alloys in In-Situ Tension

Texture evolution during multi-pass cold rolling and annealing of Ti-2Al-1.5Mn alloy