Abstract:Crystallographic textures and their effect on the mechanical anisotropy of a hot-rolled biomedical Co-Cr-Mo alloy were investigated. The hot-rolled Co-28Cr-6Mo-0.13N (mass%) alloy examined here exhibited a monotonic strength increment following hot-rolling reduction, eventually reaching a 0.2% proof stress of 1400 MPa while maintaining acceptable ductility (>10%). The dominant hot-rolling texture was a brass-type component, which is characterized by the alloy's peculiarly low stacking fault energy (SFE) even at hot rolling temperatures, although the minor peaks of the near copper component were also identified. However, because of the onset of dynamic recrystallization (DRX) during the hot rolling process, the texture intensity was relatively weak even after 90% hot rolling, although the grain refinement originating from the DRX was not significant (the "less active DRX" condition increased the strain accumulation during the process, resulting in high-strength samples). The weakened texture development resulted in negligible in-plane anisotropy for the hot-rolled specimen strength, when the specimens were tensile strained in the rolling direction (RD) and transverse direction (TD). The elongation-to-failure, however, exhibited a difference with respect to the tensile loading axis. It is suggested that the ductility anisotropy is closely related to a strain-induced γ (fcc) → ε (hcp) martensitic transformation during tensile loading, resulting in a difference in the proportion of quasi-cleavage fracture surfaces. The obtained results will be helpful in the development of high-strength Co-Cr-Mo alloy plates and sheets, and have implications regarding plastic deformation and texture evolution during the hot rolling of non-conventional metallic materials with low SFE at elevated temperatures, where planar dislocation slips of Shockley partial dislocations and thermally activated process interplay.

Developing Alternative Texture in a 90Cu-10Zn α-Brass Alloy via Route Changes in Accumulative Roll Bonding Process

Shear band mediated microstructure in an accumulative roll bonded α-brass alloy during strain path changes and annealing

A Two-Scale Texture Modelling of AA1050 Aluminum Alloy after Accumulative Roll-Bonding (ARB)

Texture and Mechanical Anisotropy of Ultrafine-Grained Aluminum Alloy AA6016 Produced by Accumulative Roll Bonding

Abnormal texture evolution of accumulative roll bonded Al-Cu by adding alumina particles

Evolution of texture and microstructure during accumulative roll bonding of aluminum AA5086 alloy

Effects of Different Modes of Hot Cross-Rolling in 7010 Aluminum Alloy: Part I. Evolution of Microstructure and Texture

Enhanced Brass texture of hot-rolled Al-4Cu-1.6Mg alloy by 0.1% Zr addition

Revealing the evolution mechanisms of microstructure, texture and mechanical behavior in Zr702 alloy plates fabricated by accumulative roll bonding

Tailoring texture in a near-α titanium alloy: Insights from strain paths and cooling rate influences

Analysis of Through-Thickness Heterogeneities of Microstructure and Texture in Nickel after Accumulative Roll Bonding

Stoichiometry and Texture Evolution of Individual Layers during Accumulative Roll Bonding of Al-Mg Laminated Composites

Texture evolution and mechanical anisotropy of biomedical hot-rolled Co-Cr-Mo alloy

Role of Strain Path Change on Texture and Microstructure of Accumulative Roll-Bonding (ARB) Processed Aluminum: A Comparative Study of Unidirectional and Reverse ARB

Accumulative Roll Bonding of Pure Copper and IF Steel

Improving strength-ductility synergy of nano/ultrafine-structured Al/Brass composite by cross accumulative roll bonding process

Reduction per pass effect on texture traits and mechanical anisotropy of Mg–Al–Zn–Mn–Ca alloy subjected to unidirectional and cross rolling

Understanding the Mechanisms of Texture Evolution of a Fe-24Cr-22Ni-7Mo Super Austenitic Stainless Steel During cold Rolling and Annealing

Analysis of the Strain Distribution and Texture Measurements in Asymmetric Rolling (AR) and Asymmetric Accumulative Roll Bonding (AARB)

Evolution of Through-Thickness Texture and Microstructure of an ARB-Processed Nb1-Zr Alloy

Evolutionoftexture in Cu-Nb multilayer composites fabricated viaaccumulative roll bonding