Abstract:This study investigates the impact of different processing steps on the crystallographic texture evolution of αZr and minority phases βZr and ωZr, and intergranular stresses as a function of grain orientation in a Zr2.5Nb pressure tube. This was done by analysis of diffraction data recorded in the 1-ID line of the Advanced Photon Source for high energy X-Rays (∼80Kev) in transmission geometry on three samples with different processing conditions: extruded, cold rolled and after autoclaving. The crystallographic texture of both αZr and βZr phases changes slightly after cold rolling, with the Burgers orientation relationship between the two phases remaining intact. The texture of βZr and ωZr shows that βZr decomposition during thermal treatment is sensitive to grain orientation. A new method was proposed to obtain the orientation dependence of the intergranular stresses from the experimental pole figures. Intergranular stresses in αZr grains were low after extrusion, but rolling significantly increased them, with values with magnitude as higher as 350 MPa and a strong dependence on grain orientation. The autoclaving treatment leads to important stress relaxation, but the dependence on grain orientation remains. The βZr phase grains exhibit significant intergranular strains in both extruded and cold-rolled conditions; the hydrostatic part was associated the presence of Nb in solid solution, with content of ∼20% and an orientation dependence of approximately ±1 at%. The deviatoric strain was attributed to intergranular stresses, with stresses below 80 MPa for the extruded sample and ranging from -600 to 400 MPa after cold rolling.

Evolution of Through-Thickness Texture and Microstructure of an ARB-Processed Nb1-Zr Alloy

Revealing the evolution mechanisms of microstructure, texture and mechanical behavior in Zr702 alloy plates fabricated by accumulative roll bonding

Analysis of Through-Thickness Heterogeneities of Microstructure and Texture in Nickel after Accumulative Roll Bonding

Evolution of texture and intergranular stresses of αZr and minority phases in Zr-2.5Nb pressure tube through synchrotron X-ray diffraction

Microstructural evolution and mechanical properties of multilayered ARB6/3/6 2N Al processed by accumulative roll bonding

Accumulative roll bonding of Cu–Zr nanolaminate: Atomistic-scale investigation of structural evolution and grain orientation scatter dependence on rolling parameters

Through-thickness variations of microstructure and texture in nickel processed by accumulative roll bonding

Texture Evolution and Temperature-Dependent Deformation Modes in Ambient- and Cryogenic-Rolled Nanolayered Zr-2.5Nb

Texture Development of Arb Processed Mg/Al Multilayers

Microstructural peculiarities and textural characteristics of Ni–W sheet alloy after accumulative roll-bonding and annealing

Analysis of the Strain Distribution and Texture Measurements in Asymmetric Rolling (AR) and Asymmetric Accumulative Roll Bonding (AARB)

Role of Strain Path Change on Texture and Microstructure of Accumulative Roll-Bonding (ARB) Processed Aluminum: A Comparative Study of Unidirectional and Reverse ARB

Evolution of texture and microstructure during accumulative roll bonding of aluminum AA5086 alloy

Microstructure Evolution and Mechanical Properties of AZ31 Alloy with Accumulative Roll Bonding

Microstructural Evolution and Mechanical Properties of Multi-layered Aluminum Alloy 6061 Processed by Accumulative Roll Bonding

Effects of Rolling Deformation on Microstructure and Hardness of Ti-45Al-9Nb-0.3Y Alloy

Microstructure evolution during the heavy warm rolling of a nickel aluminum bronze

Coupling Thermomechanical Processing and Alloy Design to Improve Textures in Mg-Zn-Ca Sheet Alloys

Microstructural Evolution and Mechanical Behavior of Cu/Nb Multilayer Composites Processed by Accumulative Roll Bonding

Evolutionoftexture in Cu-Nb multilayer composites fabricated viaaccumulative roll bonding

Microstructure and Mechanical Properties of Nickel Processed by Accumulative Roll Bonding