Abstract:An in-plane precompression and annealing process (PCA) was carried out on a Mg-3Al-1Zn thin sheet to introduce a completely tilted texture. Unlike the conventional c-axis parallel to normal direction (ND) basal texture which usually hinders the deformation ability of the Mg sheet during secondary forming, such a special texture component could supply soft orientations of extension twinning for subsequent rolling. The results indicated that the new grain orientations induced by extension twinning, which are dependent on consuming the pre-introduced tilted texture during rolling, would lie around the ND. This positioning could offer diverse orientation gradients along different directions. Meanwhile, such randomly distributed orientation gradients could provide relatively random growth directions for the new recrystallized grains during annealing and contribute to weakening of the basal texture, as well as promoting the symmetry of texture distribution (distribution of basal poles show rotational symmetry around the (0002) pole figure center). As expected, the "pre-compressed + annealed" and subsequently "rolled + annealed" sample showed improved uniaxial tensile properties (including lower yield strength, higher ductility and more symmetrical planar mechanical performance along different directions) and a considerably improved multiaxial stamping property (Erichsen value increased similar to 120%) compared with that of the as-extruded sheet or the directly rolled and annealed sample. This study confirmed that preparing soft orientations of extension twinning for subsequent rolling (e.g., employing in-plane precompression along with rolling processes) could be a highly efficient way to optimize the texture and mechanical properties of Mg sheets.

Effect of Rolling Paths and Pass Reductions on the Microstructure and Texture Evolutions of AZ31 Sheet with an Initial Asymmetrical Texture Distribution

Strain Path Dependence of Texture and Property Evolutions on Rolled Mg-Li-Al-Zn Alloy Possessed of an Asymmetric Texture

Mechanical Properties and Texture Evolution During Rolling Process of an AZ31 Mg Alloy

Effect of texture types on microstructure evolution and mechanical properties of AZ31 magnesium alloy undergoing uniaxial tension deformation at room temperature

Texture Optimization on Mg Sheets by Preparing Soft Orientations of Extension Twinning for Rolling

Reduction per pass effect on texture traits and mechanical anisotropy of Mg–Al–Zn–Mn–Ca alloy subjected to unidirectional and cross rolling

Mechanical properties and texture evolution during hot rolling of AZ31 magnesium alloy

Influence of Asymmetric Rolling on the Microstructure, Texture Evolution and Mechanical Properties of Al–Mg–Si Alloy

Texture Evolution of AZ31 Magnesium Alloy Sheets During Warm Rolling

Effect of rolling reduction on microstructure, texture, mechanical properties and mechanical anisotropy of AZ31 magnesium alloys

Evaluation of Textural Effect on the Rollability of AZ31 Alloys by Wedge‐Shaped Sample Design

Texture of AZ31B Magnesium Alloy Sheets Produced by Differential Speed Rolling Technologies

Microstructure and Texture Evolution of AZ31 Magnesium Alloy During Rolling

Deformation Behavior of AZ31 Mg Alloys Sheet During Large Strain Hot Rolling Process: A Study on Microstructure and Texture Evolutions of an Intermediate-Rolled Sheet

Effects of Texture on Anisotropy of Mechanical Properties in Annealed Mg–0.6%Zr–1.0%Cd Sheets by Unidirectional and Cross Rolling

On the Texture Memory Effect of a Cross-Rolled Mg-2Zn-2Gd Plate after Unidirectional Rolling

Effect of rolling geometry on the mechanical properties, microstructure and recrystallization texture of Al-Mg-Si alloys

'',6,1 > Influence of Pre-Rolling on Microstructural Evolution of Non-Basal Textured Magnesium Alloy

Twinning, Grain Orientation, and Texture Variations in Mg Alloy Processed by Pre-Rolling

The Effect of Texture on the Very High Cycle Fatigue Performance and Deformation Mechanism of Rolled AZ31B Magnesium Alloys

Improved stretch formability of AZ31 sheet via texture control by introducing a continuous bending channel into equal channel angular rolling