Abstract:A TD-split basal texture with two peaks highly tilted from the normal direction (ND) towards the transverse direction (TD) is usually developed in Mg-Zn-Ca plates and can effectively improve ductility and formability. In the present study, the texture evolution during cold rolling and subsequent annealing of a Mg-2Zn-1Ca plate with initial TD-split texture was investigated, and new insights into the mechanisms of texture evolution were obtained. The results show that a dumbbell-shaped basal texture transformed into an elliptical shape after 41% cold rolling. The random distribution of prismatic planes became preferred with largely parallel to the rolling direction (RD). Crystal plasticity simulations revealed that basal slip was the predominant deformation mode, and inclined basal poles toward the ND. The activation of other non-basal slips would retard this tendency. Prismatic slip with a relative activity of 20% to 30% preserved the pre-existing TD-split texture after a high rolling reduction of 41%. Pyramidal slip prevented the formation of basal fiber and lead to a spreading of basal poles toward the RD mainly at strains over 29%. After full recrystallization, the elliptical TD-split basal texture became a dumbbell-shaped TD-split texture. Grain nucleation was observed at grain boundaries (GBN mechanism), within deformation twins (DTN mechanism), and near precipitates (PSN mechanism). GBN and DTN mainly developed a TD-split basal-texture. Instead of the formation of random orientations as considered previously, PSN produced a TD-split basal-texture, and the basal poles exhibited a much wider distribution with high angle of the peaks off the ND. The grains nucleated by GBN, DTN, and PSN did not exhibit preferred growth, and consequently, the texture hardly changed during subsequent grain growth.

Texture Optimization on Mg Sheets by Preparing Soft Orientations of Extension Twinning for Rolling

Insights into the evolution of texture and mechanical properties during warm rolling and annealing of Mg–2Zn-0.5Ca alloy

Understanding the mechanisms of texture evolution in an Mg-2Zn-1Ca alloy during cold rolling and annealing

Deformation mechanism, orientation evolution and mechanical properties of annealed cross-rolled Mg-Zn-Zr-Y-Gd sheet during tension

Microstructure evolution and mechanical property of Mg-3Al alloys with addition of Ca and Gd during rolling and annealing process

Reduction per pass effect on texture traits and mechanical anisotropy of Mg–Al–Zn–Mn–Ca alloy subjected to unidirectional and cross rolling

Coupling Thermomechanical Processing and Alloy Design to Improve Textures in Mg-Zn-Ca Sheet Alloys

Effect of texture types on microstructure evolution and mechanical properties of AZ31 magnesium alloy undergoing uniaxial tension deformation at room temperature

Texture evolution during multi-pass cold rolling and annealing of Ti-2Al-1.5Mn alloy

Microstructure, Texture Evolution, and Mechanical Properties of Thin AZ31B Mg Alloy Sheets Prepared by Two-Stage Rolling

The effects of orientation control via tension-compression on microstructural evolution and mechanical behavior of AZ31 Mg alloy sheet

Unveiling the Rolling Texture Variations of Α-Mg Phases in a Dual-Phase Mg-Li Alloy

Texture weakening and ductility improvement of Mg-1.1Mn-0.5Al alloy via medium temperature-high reduction rolling: twinning variants selection and dynamic recrystallization mechanism

Enhanced grain refinement and texture weakening in Al–Mg–Si alloy through a novel thermomechanical processing

Enhanced rollability of Mg alloys by directly activated { 10 1 ̄ 2 } twinning during asymmetric rolling: Experiments and finite element analysis

Effect of Al addition and rolling reduction on microstructure and texture evolution of Mg–3Sn alloy during high-speed rolling

New insight of texture and microstructure evolution, and the connections between with tensile performance in as-annealed Al-Cu-Mg-Zr sheet

Influence of In-Plane Simple Shear Strain on the Grain Orientation Regulation and Stretch Formability of Pre-twinned AZ31 Magnesium Alloy Sheet

Improving the tension-compression asymmetry of ZK61 magnesium alloy through texture optimization in combined extrusion

Texture Control Techniques for Improving Room Temperature Formability of Mg Alloys including Pre-twinning: A Review

Enhanced ductility and strength of Mg-1Zn-1Sn-0.3Y-0.2Ca alloy achieved by novel micro-texture design