Abstract:The research on Al–Zn–Mg–Cu alloys mainly focuses on the effects of solution aging and strain rate on the microstructure and properties of the alloy, as well as the flow stress behavior of the alloy. There are few studies on the effects of hot rolling deformation and reduction pass on the microstructure and properties of aluminum alloy. The dislocation density of alloy is affected by changing the rolling deformation, and post-heat treatment improves fine grains segregation and break coarse second phases. The alloys comprehensive mechanical properties are improved by controlling the recrystallization fraction and size. Different shape variable rolling and different passes, optical microscope (OM), field emission scanning electron microscope (SEM) with energy dispersive spectrometers (EDS), X-ray diffractometer (XRD), microhardness tester, and other methods were used to characterize the samples, and simulation of the rolling process analyzed by Deform-3D software. The effects of hot rolling deformation and deformation pass on microstructure and properties of aluminum alloy were also studied. The results show that dynamic recrystallization was beneficial to grain refinement when deformation increases to 40%. The coarse second phase was broken and refined into chains and partially spheroidized to dissolve in the matrix under large deformation. Dislocation density decreased after solution treatment when deformation was less than 80%, and increased after large deformation was 80%. The equivalent strain obtained by numerical simulations increases with the increase of deformation. The maximum equivalent strain was on both sides of the rolling surface, and this area was the most prone to crack in rolling. When the increase of the shape variable, the recrystallization volume fraction increased, and the grain size decreased.

Effect of Particles on Microstructural Evolution During Cold Rolling of the Aluminum Alloy AA3104

Microstructure and Texture Evolution of Particle-Containing Aa3104 Alloy Cold Rolled to Large Strains

Dislocation Boundary Structure from Low to Medium Strain of Cold Rolling AA3104 Aluminum Alloy

Effect of second-phase precipitates on deformation microstructure in AA2024 (Al–Cu–Mg): dislocation substructures and stored energy

Microstructure and Texture Evolutions of Aa1050 Aluminum Alloy Cold Rolled to High Strains

Evolutions of Grain Orientation and Dislocation Boundary in Aa1050 Aluminum Alloy During Cold Rolling from Low to Medium Strains

MICROSTRUCTURAL EVOLUTION OF COLUMNAR GRAIN Al DURING COLD ROLLING II. Mircoscopic Subdivision

Crystal Plasticity Finite Element Simulation of Grain Evolution Behavior in Aluminum Alloy Rolling

Evolution of Microstructure and Texture During Recovery and Recrystallization in Heavily Rolled Aluminum

The Effects of Cold Rolling and Annealing on the Microstructure Evolution of Ordered C-2000 Alloy during Metallic Wire Preparation

Evolution of microstructure and mechanical properties influenced by nanosized precipitates during rolling deformation

Influence of different rolling processes on the microstructures and mechanical properties of 6016 aluminum alloy

Effect of Microstructures on the Anisotropy of the Roll Casting Strip of Cold Rolled 3003 Aluminum Alloy

Texture, Microstructure and Mechanical Properties of 6111 Aluminum Alloy Subject to Rolling Deformation

Specific Features of Microstructural Evolution During Hot Rolling of the As-Cast Magnesium-Rich Aluminum Alloys with Added Transition Metal Elements

Effect of hot deformation on microstructure and quenching-induced precipitation behavior of Al-Zn-Mg-Cu alloy

Effect of Initial Microstructure on the Hot Deformation Behavior and Microstructure Evolution of Aluminum Alloy AA2060

Influence of Different Rolling Processes on Microstructure and Strength of the Al–Cu–Li Alloy AA2195

Annealing Behavior of Nanostructured Aluminum Produced by Cold Rolling to Ultrahigh Strains

Effect of rolling deformation and passes on microstructure and mechanical properties of 7075 aluminum alloy

Effect of Residual Deformation Energy and Critical Heating Rate on Cubic Texture and Grain Growth Behavior of Severely Deformed Aluminum Foil