Abstract:Al matrix composite, reinforced with the in situ synthesized 3C–SiC, MgAl2O4, and MgO grains, was produced via the casting process using phenolic resin pyrolysis products in flash mode. The contents and microstructure of the composites’ fracture characteristics were analyzed by X-ray diffraction (XRD) and scanning electron microscopy (SEM). Mechanical properties were tested by universal testing machine. Owing to the strong propulsion formed in turbulent flow in the pyrolysis process, nano-ceramic grains were formed in the resin pyrolysis process and simultaneously were homogeneously scattered in the alloy matrix. Thermodynamic calculation supported that the gas products, as carbon and oxygen sources, had a different chemical activity on in situ growth. In addition, ceramic (3C–SiC, MgAl2O4, and MgO) grains have discrepant contents. Resin pyrolysis in the molten alloy decreased oxide slag but increased pores in the alloy matrix. Tensile strength (142.6 ± 3.5 MPa) had no change due to the cooperative action of increased pores and fine grains; the bending and compression strength was increasing under increased contents of ceramic grains; the maximum bending strength was 378.2 MPa in 1.5% resin-added samples; and the maximum compression strength was 299.4 MPa. Lath-shaped Si was the primary effect factor of mechanical properties. The failure mechanism was controlled by transcrystalline rupture mechanism. We explain that the effects of the ceramic grains formed in the hot process at the condition of the resin exist in mold or other accessory materials. Meanwhile, a novel ceramic-reinforced Al matrix was provided. The organic gas was an excellent source of carbon, nitrogen, and oxygen to in situ ceramic grains in Al alloy.

Mechanical Properties of Ceramic–metal Composites by Pressure Infiltration of Metal into Porous Ceramics

Microstructures and Mechanical Properties of Pressureless Sintered Ca-3(PO4)(2)/Si3N4 Composite Ceramics

Fabrication and mechanical properties of high-volume-fraction Si 3 N 4 -Al-based composites by squeeze infiltration casting

The Mechanical Properties of Co-Continuous Si3N4/Al Composites Manufactured by Squeeze Casting

Mechanical Properties and Toughening Mechanisms of Si3n4 Matrix Laminated Ceramic Composite

Mechanical Properties and Toughening Mechanisms of Si 3 N 4 Matrix Laminated Ceramic Composite

Fabrication and Mechanical Properties of Si3N4/SiC Nanocompoisites under Pressureless Sintering.

Pressureless Sintering and High-Temperature Strength of SiC-AlN Ceramics

Microstructure and Mechanical Properties of Hot-Pressed Al2O3–mullite–ZrO2–SiC Composites

Effect of porous Si 3 N 4 preform on the mechanical properties of Si 3 N 4 /Al composites with interpenetrating network structure

Effects of residual stress and intragranular particles on mechanical properties of hot-pressed Al2O3/SiC ceramic composites

Pressureless Infiltration Preparation of High SiC/Al Ceramic Matrix Composites

Gel casting and properties of porous silicon carbide/silicon nitride composite ceramics

Ambient and Elevated Temperature Mechanical Properties of Hot-Pressed Fused Silica Matrix Composite

Effects of SiC contents on the microstructure and mechanical properties of Al4SiC4–SiC ceramic composites

Study on the mechanical properties and microstructure of Al2O3/nano-SiC multiphase ceramics

POROUS Si3N4-SiO2 COMPOSITE CERAMIC AND ITS PROPERTIES

Fabrication and Mechanical Properties of Si3n4/Sic Nanocomposite with Pressureless Sintering and Sinter-Post-Hiping

Mechanical Properties of Al Matrix Composite Enhanced by In Situ Formed SiC, MgAl2O4, and MgO via Casting Process

Micromechanical properties of high fracture performance SiCp–6061Al/6061Al composite

Influence of Fabricated Process on Mechanical Properties of Porous Sic-Particle/Si3n4 Composites