Abstract:The bottleneck problems of SiC particles reinforced AlSi10Mg composites (SiC/AlSi10Mg) prepared by traditional casting method, such as composition segregation, interface reaction and coarse microstructure, can be effectively improved by powder metallurgy with lower processing temperature. In this study, the influence of SiC particle size and content on the properties of SiC/AlSi10Mg was systematically analyzed. SiC/AlSi10Mg composites were prepared by planetary ball milling, spark plasma sintering (SPS) and hot extrusion composite preparation process. The obtained composites presents dense microstructure without the formation of interfacial reaction phase. The distribution of micron SiC particles (μm-SiC) in the matrix is relatively uniform, and nano SiC particles (nm-SiC) slightly agglomerates with the increase of the content. The strength of SiC/AlSi10Mg increases with the increase of nm-SiC content, which is mainly attributed to dispersion strengthening, dislocation strengthening and grain refinement strengthening. The strength of SiC/AlSi10Mg hardly changes with the increase of μm-SiC content, but the elongation decreases gradually. The deformation between μm-SiC and AlSi10Mg matrix is not coordinated and μm-SiC cleave the AlSi10Mg matrix. The irregular boundaries of μm-SiC are easy to produce stress concentration during loading, leading to interface cracking or μm-SiC fracture. Therefore, μm-SiC are difficult to play a significant strengthening effect to composites. With the increase of SiC content, the fracture mechanism of composites gradually changes from ductile fracture to brittle fracture in SiC agglomeration region. This study lays a theoretical and experimental foundation for the controllable preparation and performance optimization of high strength and toughness AMCs reinforced by SiC particles.

Effects of residual stress and intragranular particles on mechanical properties of hot-pressed Al2O3/SiC ceramic composites

Microstructure and Mechanical Properties of Hot-Pressed Al2O3–mullite–ZrO2–SiC Composites

Study on the mechanical properties and microstructure of Al2O3/nano-SiC multiphase ceramics

Effects of SiC contents on the microstructure and mechanical properties of Al4SiC4–SiC ceramic composites

Effect of SiC Addition on Mechanical Properties of Hot-Pressed Al2O3-GdAlO3 Ceramics with Eutectic Composition

Influence of characteristic parameters of SiC reinforcements on mechanical properties of AlSi10Mg matrix composites by powder metallurgy

Mechanical Properties and Microstructure of Al<sub>2</sub>O<sub>3</sub>-Ti<sub>3</sub>SiC<sub>2</sub> Ceramic Composites

Effect of SiCP Content on β-SiAlON/SiC Nanocomposite Ceramic

Microstructure and Properties of Hot Pressed Zr2(Al(Si))4C5/SiC Composites

Insights into Intragranular Precipitation and Strengthening Effect in Al2O3/SmAlO3 Ceramic with Eutectic Composition

Effects of Hot Compression on Microstructure of SiC_p/Al Composite with High Volume Fraction

Study of SiC/Al nanocomposites under high pressure

Preparation and properties of intragranular Al2O3-SiC nanocomposites

Effect of Al2O3 particle size on the microstructure, phase transformation and mechanical properties of hot pressed Al2O3-CA6-ZrO2/Ni multi-phase composites

Microstructure and Mechanical Properties of Multiphase Strengthened Al/Si/Al 2 O 3 /SiO 2 /MWCNTs Nanocomposites Sintered by In Situ Vacuum Hot Pressing

Influence of SiC particle size on microstructure and mechanical properties of Al2O3-SiC nanocomposites

Effect of holding time and pressure on the densification, microstructure and mechanical properties of hot pressed Al2O3-CA6-ZrO2/Ni multi-phase composites

Effect of SiC particulate on the microstructure of Al-6Ti-6Nb matrix composites fabricated by mechanical alloying technique

Mechanical Behavior of Α-Al2o3-coated SiC Particle Reinforced Nickel Matrix Composites

STUDY OF FABRICATION AND COMPRESSIVE PERFORMANCE OF ALUMINIUM ALLOY MATRIX GRADIENT COMPOSITES REINFORCED WITH SiC PARTICLES

Microstructure and mechanical properties of the α-SiAlON/α-SiC composites: Effects of heat treatment