Abstract:AlN-SiC multiphase ceramics possess robust mechanical strength, high thermal conductivity and good oxidization resistance, and show great potential as the matrix material of fiber reinforced ceramic matrix composites. In this work, AlN-SiC multiphase ceramics were fabricated via low temperature reactive melt infiltration of Si-Al alloy into porous C-Si3N4 preforms. Influence of Si-Al source on the melt infiltration process was studied, and impact of residual silicon on the mechanical and thermal properties of the AlN-SiC ceramics was investigated. It was found that an Al-O layer was in- situ formed at the interface between Si-Al melt and C-Si3N4 preform, when Si-Al powder was used as the infiltration medium. This seriously retarded the melt infiltration process and made the penetration of Si- Al melt into the C-Si3N4 preform hardly possible. However, when Si-Al ingot was used as the infiltration medium, a well infiltration of Si-Al melt into the C-Si3N4 preform occurred, which led to the formation of dense AlN-SiC ceramics. Mechanical and thermal property measurements indicated that the strength of the AlN-SiC ceramics was significantly improved as the residual silicon content in it was reduced, while a reverse trend was observed for the thermal conductivity. AlN-SiC ceramics with 4%( in mass) residual silicon showed a high strength of 320.1 MPa, nearly comparable to that of conventional reaction bonded SiC, although its thermal conductivity was modest (26.3 W center dot m(-1)center dot K-1). The fundamental reasons for the above phenomena were discussed. This study is of great significance for the preparation of SiCf/AlN-SiC composites by low temperature reactive melt infiltration.

Pressureless Infiltration Preparation of High SiC/Al Ceramic Matrix Composites

Microstructure and Hardness Performance of a SiCp/Al Composite by Pressureless Infiltration Technique

Interfacial microstructure of SiCp/Al composite produced by the pressureless infiltration technique

High Volume Aluminum Matrix Composites Prepared by Pressureless Infiltration

Study on the SiC-Al Co-Continuous Phase Composites

Microstructure and Compressive Mechanical Properties of SiCp/Al Composite Made by Pressureless Infiltration Technique

Microstructure and properties of C/C–SiC composites prepared by reactive melt infiltration at low temperature in vacuum

Lamellar-interpenetrated Al–Si–Mg/SiC Composites Fabricated by Freeze Casting and Pressureless Infiltration

Mechanical Properties of Si_3N_4/AlN-Al Composites Prepared by Pressure-free Infiltration

Aluminium-matrix silicon carbide whisker composites fabricated by pressureless infiltration

Reactive Infiltration Processing and Thermal Properties of SiCp/6013Al Composite with High SiC Particle Content

Pressureless Infiltration Mechanism of High Content Sip/Al Composite

Preparation of Al/70vol% Sip composites by pressureless infiltration

Fabrication of 3D-SiC/aluminum alloy interpenetrating composites by DIW and pressureless infiltration

Fabrication and Properties of AlN-SiC Multiphase Ceramics <i>via</i> Low Temperature Reactive Melt Infiltration

Preparation and characterization of composite materials obtained by pressure infiltration of aluminum in sintered SiC/kaolin preforms

The Preparation of High-Volume Fraction SiC/Al Composites with High Thermal Conductivity by Vacuum Pressure Infiltration

Study of SiC/Al nanocomposites under high pressure

The Microstructure and Properties of SiC/SiC-based Composites Fabricated by Low-Temperature Melt Infiltration of Al–Si Alloy

Effect of Pressure on the Solidification Behavior and Mechanical Properties of SiCp/Al-Mg Composites

Effect of Ti Doping on the Microstructure and Properties of SiCp/Al Composites by Pressureless Infiltration