Abstract:Si3N4/SiC composites containing 0-30 vol% SiC were fabricated by pressureless sintering and sinter-post-HIPing method using fine Si3N4 and nano-sized SiC powders. Specimens reached full density (>96% theoretical density (th. d.)) except the composites made by pressureless sintering which contained a small amount of sintering additives or a large amount of SiC. All composites with 10 mass% sintering additives reached full density (similar to 99% th. d.) by sinter-post-HIPing. The addition of SiC particles greatly influenced the grain morphology of the Si3N4 matrix. The average grain thickness, length and aspect ratio decreased with increasing SiC content because of grain boundary pinning by SiC particles. Also the mechanical properties were markedly dependent upon the fraction of SiC particle reinforcement, as well as matrix grain size and porosity. When the materials were pressureless sintered, the strength of the composite increased with SiC additions below 20 vol%. Further increase in the SIC content resulted in a corresponding decrease in strength. Maximum strength of 1150 MPa was attained at 20 vol% SiC addition. The increase in strength by addition of SiC is due to decrease of grain size of Si3N4 matrix grain size, and the decrease by further increase in SiC content is caused by porosity and SiC agglomerate. On the other hand, toughness decreased monotonically with SiC content. The strength of all samples was enhanced by sinter-post-HIPing without any change in fracture toughness. The strength of sintered samples with 10-15 vol% SiC increased by similar to 20% to 1260 MPa by post-HIPing. The increase in strength by post-HIPing was interpreted as being due to a decrease flaw size.

Influence of Fabricated Process on Mechanical Properties of Porous Sic-Particle/Si3n4 Composites

Influence of fabricated process on mechanical properties of porous SiC-particle/ Si3N4 composites

Gel casting and properties of porous silicon carbide/silicon nitride composite ceramics

Processing, Microstructures and Mechanical Properties of Aqueous Gelcasted and Solid-State-Sintered Porous Sic Ceramics

Fabrication, Structure and Properties of Porous SiC Ceramics with High Porosity and High Strength

PREPARATION OF POROUS Si_3N_4 NANOCOMPOSITES BY GELCASTING

Influence of the Porosity of C/C on the Characterization of C/C-Sic Composites Prepared by Reactive Melt Infiltration Method

Fabrication and Properties of Porous Si3N4 Ceramic with High Porosity

Microstructure and Mechanical Properties of Three Porous Si3n4 Ceramics Fabricated by Different Techniques

Microstructure and Properties of SiCw/SiC Composites Prepared by Gel-Casting Combined with Precursor Infiltration and Pyrolysis

Preparation of in-situ synthesized SiC particles reinforced highly porous Si3N4 ceramics by gel-casting

Fabrication of High‐strength Porous SiC‐based Composites with Unidirectional Channels

Fabrication of Co-Continuous SiC/Al Composites from Novel SiC Preforms with High Porosity and Controllable Pore Size

Preparation and Properties of Micro porous Si3N4 Ceramics by Gelcasting

Fabrication and Mechanical Properties of Si3n4/Sic Nanocomposite with Pressureless Sintering and Sinter-Post-Hiping

Fabrication Process of SiCp/7085 Composite and Experiment Research

High Strength and Self-Lubrication Graphite/sic Composites

Effect of porous Si 3 N 4 preform on the mechanical properties of Si 3 N 4 /Al composites with interpenetrating network structure

Strengthening mechanism and anisotropy of mechanical properties of Si3N4p/Al-Mg-Si composites fabricated by sintering and extrusion

Effect Of Pore-Forming Processing On The Gas Permeability And Flexural Strength Of Porous Sic Ceramics

Fabrication of porous Si 3 N 4 ceramics through a novel gelcasting method