Programme Design of Reference Voltage Source Module Embedded in LCOS Chip

LIU Hui-Gang,GENG Wei-Dong,SHANG Guang-hui,ZHU Yong,HUANG Qian,LIU Yan-Yan

DOI: https://doi.org/10.3969/j.issn.1006-6268.2006.11.014

2006-01-01

Abstract:The paper presented programme design of reference voltage source module embedded in LCOS chip and analysed the role of reference voltage. The overall diagram of programme design and low-power of some circuits are given.

What problem does this paper attempt to address?

Novel design of reference voltage source integrated in LCoS chip

Huigang Liu,Weidong Geng,YongPing Dai,Yanyan Liu

2007-01-01

Abstract:This paper proposes the design of programmable multi-channel reference voltage source integrated in LCoS chip, analyses the role of the reference voltage in LCoS display system, and part circuit of schematic, layout, lower-power method are given. The whole circuit is composed of (IC)-C-2 interface circuit, multi-channel registers, control circuit, multi-channel DAC and multi-channel buffer. This paper focuses on multi-channel DAC and multi-channel buffer of the reference voltage source, and Cadence IC design tools are used to complete part of the circuit schematic design and simulation. The CMOS processes of SMIC are used to complete the circuit layout design and follow-up of ERC, DRC, LVS inspected and verified. The final results show that the output of the circuit can completely satisfy the requirements of LCoS display.
Design of reference voltage source integrated in LCoS chip

LIU Hui-gang,GENG Wei-dong,LIU Yan-yan,DAI Yong-ping,FEI Xu-feng

DOI: https://doi.org/10.1109/PRIMEASIA.2010.5604937

2010-01-01

Abstract:This paper proposes the design of programmable multi-channel reference voltage source integrated in LCoS chip, analyses the role of reference voltage in LCoS display system. Emphasis was placed on the design of analog circuits which consist of dual ladder resistor D/A converter and constant gm rail-to-rail operational amplifier. The reference voltage source for gamma correction of LCoS display is taped out by Chartered 0.35 μm CMOS 2P4M Mixed-mode process, and the chip was tested. The test results indicate that the output of the chip can completely meet requirements of the common electronic field-inversion field sequential LCoS display system, and the setup time and accuracy of output voltage achieve the expected target.
Design of the Power Management Module Integrated in SOC

何乐年,王云峰,严晓浪

DOI: https://doi.org/10.3969/j.issn.1007-0249.2003.03.005

2003-01-01

Abstract:SOC (System-on-chip) is one kind of large scale and complex IC driven by high clock frequency. The traditional method of externally providing power to SOC can not guarantee its proper operation because of the unstable external power supply. Accordingly, a scheme is proposed to integrate a power resource management module into SOC to manage the external power resource dynamically as to supply SOC chip with stable power, detect the low voltage and protect the data in RAM from losing. Design methodology of power management module is also given. Circuit simulation result shows that the variation of output voltage of proposed power resource management module is within 0.2592V when external power supply changes from 3.6V to 2.7V.
A Novel Fully On-Chip CMOS Low-Dropout Linear Regulator with Ultra Low Noise

Mao Cui,He Lenian,Yan Xiaolang

DOI: https://doi.org/10.3321/j.issn:0253-4177.2008.08.037

2008-01-01

Chinese Journal of Semiconductors

Abstract:A fully on-chip low-dropout linear regulator (LDO) with ultra low noise is presented.This regulator uses a Vt/R based voltage reference rather than a commonly used bandgap reference to minimize the noise introduced by the reference voltage. The Vt/R based voltage reference employs a digital calibration schema to increase the accuracy of the output voltage.This fully on-chip LDO is designed in a TSMC 0.18μm RF CMOS process for the power supply of a low phase noise phase lock loop (PLL) with 10mA of DC current consumption.The simulation results indicate that the total output noise of the LDO is 26nV/Hz@100kHz and 14nV/Hz@1MHz,and the power supply reject ratio is -40dB@1MHz and less than -34dB in all frequency bands.The test results show that the phase noise of the PLL using this LDO is 6dBc@1kHz less and 2dBc@200kHz less than using conventional LDO.
A Low-Power Voltage Reference Source for Lithium Battery Protection ICs

MA Shaoyu,HAN Yan,HONG Hui,ZHOU Haifeng

IF: 1.992

2008-01-01

Microelectronics Journal

Abstract:A low-power CMOS voltage reference source for Li-ion battery protection ICs was presented.A depleted NMOS transistor,which was used as current source,and a negative feedback loop constitute a stable voltage reference.The novel voltage reference source was applied to a Li-ion battery protection IC to provide various detection voltages.A Li-ion battery protection chip was fabricated in 0.6 μm double-poly single-metal CMOS process using this novel reference circuit.Test results show that the voltage reference has an output of 1.2 V at supply voltages ranging from 2.5 V to 5 V,with a variation of only 5 mV.The proposed voltage reference consumes less than 1 μA of current in operation mode,and no more than 50 nA in sleep mode,which meets the requirement of low power Lithium battery protection ICs.
Design of Low Parasitic Inductance SiC MOSFETs Halfbridge Power Modules

Yifan Wang,Jinlong Gong,Qihua Song,Li luo,Bin Zhang,Qing Guo

DOI: https://doi.org/10.1088/1742-6596/2224/1/012120

2022-01-01

Journal of Physics Conference Series

Abstract:The working mechanism of a half-bridge SiC MOSFETs two chips parallel module is studied. Its parasitic inductance of the power module is simulated by using the Ansoft Q3D Extractor software, and its heat transfer mechanism is simulated using the finite element software ANSYS software. Aiming at reducing the parasitic inductance, a new topology of power chips inside the module is designed, which places the chips that are in the same working circuit loop in close vicinity to reduce the whole circuit length and area. Meanwhile, the thermal characteristics are also analyzed. Considering the factors of parasitic inductance and heat dissipation, the optimal module design scheme is finally determined.
Design Methodology Of Cmos Low Power

Dongyan Hao,Ming Zhang,Wei Zheng

DOI: https://doi.org/10.1109/ICIT.2005.1600620

2005-01-01

Abstract:The growing demand for portable electronic devices has led to an increased emphasis on power consumption within the IC design industry. In this article, according the design flow of VLSI, we present a survey of low power design methodology at five levels such as system, behavioral, architectural, logic and physical levels.
Design of Area-Efficient GHz Range Current Mode Frequency Synthesizer Using Standard CMOS Technology

Dan-Dan Zheng,Yu-Bin Li,Chang-Qi Wang,Kai Huang,Xiao-Peng Yu

DOI: https://doi.org/10.2478/jee-2019-0063

2019-01-01

Journal of Electrical Engineering

Abstract:Abstract In this paper, an area and power efficient current mode frequency synthesizer for system-on-chip (SoC) is proposed. A current-mode transformer loop filter suitable for low supply voltage is implemented to remove the need of a large capacitor in the loop filter, and a current controlled oscillator with additional voltage based frequency tuning mechanism is designed with an active inductor. The proposed design is further integrated with a fully programmable frequency divider to maintain a good balance among output frequency operating range, power consumption as well as silicon area. A test chip is implemented in a standard 0.13 µm CMOS technology, measurement result demonstrates that the proposed design has a working range from 916 MHz to 1.1 l GHz and occupies a silicon area of 0.25 mm2 while consuming 8.4 mW from a 1.2 V supply.
Design of Voltage–Current Reference Source in CMOS Technology

Tomasz Borejko,Witold Adam Pleskacz

DOI: https://doi.org/10.3390/electronics13214212

IF: 2.9

2024-10-28

Electronics

Abstract:A design methodology for a resistorless low-power two-in-one voltage and current reference source working in subthreshold and moderate regions is described. The presented novel universal reference voltage–current source was implemented in ten different designs for seven different CMOS technologies. Six versions of these designs were silicon-proven using four different CMOS technologies. The example of implementation in 130 nm technology provides a reference current of 5 μA and reference voltage of 800 mV at supply voltages ranging from 0.9 V to 2.0 V with a total current consumption of 15 μA. The proposed circuit occupies a 1200 μm2 chip area and achieves 280 and 118 ppm/°C for all process corners and temperature variation from −40 °C to 125 °C. The power supply rejection ratio of output IREF without any filtering capacitor at 100 Hz and 10 MHz is 128 dB and 100 dB, respectively. The equivalent output current noise in the bandwidth from 1 Hz to 10 MHz reaches 9.1 nARMS.

engineering, electrical & electronic,computer science, information systems,physics, applied
Power Supply Module Design in the Low Power Consumption Application

Pan Hong,Wu Xiaobo,Chen Hai,Hao Binxian

DOI: https://doi.org/10.1109/edssc.2007.4450147

2007-01-01

Abstract:To increase the efficiency of the SMPS (Switch Mode Power Supply) over the whole load range, a novel power supply module with low power consumption for multi-mode application was presented. The main modules constituting it include UVLO, Digital Power, Regulators (a 5 V regulator and a 4.3 V regulator) and REFOK. Especially, a control strategy was proposed to achieve its low power operation. The module architecture and circuit were optimized and simulated in design. And the chip was tape-out in 1.5 um BCD technology. Test results showed that the expected functions were achieved and the main features met the requirement well.
Circuit Design of Single Panel Color LCOS Microdisplay Chip

LIU Yan-yan,DAI Yong-ping,GENG Wei-dong,SUN Zhong-lin

DOI: https://doi.org/10.3969/j.issn.1006-6268.2006.03.010

2006-01-01

Abstract:The circuit design of a single panel LCOS microdisplay chip is described. Equipped with proper engine and interface circuit system, the LCOS chip can be used to implement single panel LCOS rear-projection TV or other projection products. Similar with traditional field sequential color LCOS microdisplay chip, it consists of three parts: row scan driver, data driver and pixel array. The main difference of them is the row access method. The traditional field sequential color LCOS uses line-by-line row scan, while the LCOS introduced here uses random addressing. The red, green and blue data are almost written into the pixel array simultaneously. Cooperating with scrolling engine the color image is displayed. Single panel LCOS system costs less chips and relevant circuit systems, then can reduce product cost.
A 30na Temperature-Independent CMOS Current Reference and Its Application in an LDO

Wang Yi,He Le'nian,Yan Xiaolang

DOI: https://doi.org/10.3969/j.issn.1674-4926.2006.09.029

2006-01-01

Chinese Journal of Semiconductors

Abstract:A high-precision CMOS current reference circuit is proposed for using in low-dropout (LDO) voltage regulators with low power.A current reference of 30nA,independent of supply voltage,is obtained with the sub-threshold region design method.In the high temperature region,taking advantage of the reverse current of the parasitic diode in the MOS transistor,every branch current in the current mirror is compensated,so that the precision of the 30nA current reference is improved from ±1nA to ±0.6nA in the range of -40～130℃.Using this current reference,the total quiescent current of the LDO is around 4μA in the range of -40～130℃.The proposed circuit is simulated using Spectre from Candence,and the chip is implemented in CSMC 0.5μm mixed-signal technology.The designed circuit is validated by the results of the chip test.
An Inverter-based On-chip Voltage Reference Generator for Low Power Application

Yuchen Zhao,Zhuo Zou,Lirong Zheng

DOI: https://doi.org/10.1109/socc49529.2020.9524793

2020-01-01

Abstract:This paper presents an on-chip voltage reference generator for low power applications. The circuits consist of an array of inverters, a switch-capacitor, and a notch filter. The proposed circuits avoid using any bipolar junction transistor (BJT) and only contain MOSFETS and capacitors. The inverter is utilized as the core circuit to generate the reference voltage. The changes in temperature and process are suppressed by using the switch-capacitor. A notch filter is adopted for ripple reduction. This work is designed and simulated in a 0.18 µm CMOS process. Due to the mostly-digital architecture, this circuit can operate at a sub-1 V supply and generate a reference voltage of 0.504 V with a temperature coefficient of 20 ppm. The power consumption is 83 nW.
Research and Design of High PSR,Low power,Chip-level LDO

Yu-zheng JIN,Yu-zhuo FU

DOI: https://doi.org/10.19304/j.cnki.issn1000-7180.2014.05.039

2014-01-01

Abstract:In order to reduce the input voltage noise while supplying a stable output voltage and integrate on-chip ,a kind of new CMOS ,chip-level LDO is proposed in this paper .One of the most notable features is that its quiescent current is quite low .With the 3 .3 V power supply ,the quiescent current is only 10 μA .So the power consumption is considerable for chip-level .Meanwhile ,the power supply rejection (PSR) is also promoted with an effective PSR improved method ,which can reach -45 dB in low frequency and the worst case can also reach around -20 dB .So it can better reject the power supply noise at the output and is suitable for noise-sensitive circuits .
Low-Power Methods Research of SoC Physical Design

WANG Chao,TIAN Tai-qing,WANG Ming-jiang

DOI: https://doi.org/10.3969/j.issn.1002-2279.2011.02.004

2011-01-01

Microprocessors

Abstract:The low-power design is an important part in SoC(System on Chip) design process,and physical design is the late work.Firstly give a comprehensive analysis of the different sources of CMOS circuit and the methods of low-power design;then mainly discusses the low-power design of the back-end synthesis and placement and routing stages.These methods have been applied in design practice and performed well.
Layout Design and Verification of the Voltage Reference Module in the Auto Electronic Ignition Control Chip

Ying Yang,Yong Feng Zhang,Ying

DOI: https://doi.org/10.4028/www.scientific.net/amm.608-609.933

2014-01-01

Applied Mechanics and Materials

Abstract:This article describes the layout design and verification of the input module of a auto electronic ignition chip used in the field of automotive engineering. Using standard bipolar technology, full-custom design on the input module placement and routing, and completed the back-end verification. This chip has low power consumption, low cost, and stable performance.
Design and implementation of a novel programmable power monitor chip

Ge Binjie,Wang Xin'an,Zhang Xing,Feng Xiaoxing,Wang Qingqin

DOI: https://doi.org/10.1109/PRIMEASIA.2010.5604976

2010-01-01

Abstract:This paper proposes a novel programmable power monitor chip. With only three program pins and without any off-chip devices, the chip has 36-program states by taking different connections for the 3-program pins. The chip can monitor the voltage from 1.5v to 5.0v with 0.1v step. Special SH circuit and current limited digital blocks are employed to achieve ultra low quiescent power. The implementation is based on 2M1P 0.5um mixed signal process, the die area is 0.24mm2, and the quiescent current is only 3uA.
A high-range reference voltage low-dropout regulation design for voltage-controlled oscillator circuit

Shengyu Song,Hengzhou Yuan,Jianjun Chen

DOI: https://doi.org/10.1088/1742-6596/2221/1/012020

2022-05-23

Journal of Physics: Conference Series

Abstract:The stability of VCO as a clock recovery module in high-speed transmission circuits cannot be ignored. The LDO circuit as its power module not only needs to ensure the stability of the VCO under high-speed working conditions, but also needs to satisfy the demand for changes in its supply voltage swing. To meet the above requirements, a high-range reference voltage LDO (Low-dropout Regulator) was designed under the 28nm process. The input of the error amplifier of the LDO adopts a rail-to-rail structure, the reference voltage can be changed in a larger range, and the output voltage can also fluctuate in the range of 0.3V-0.9V. After simulation, the power supply rejection ratio (PSRR) of this LDO is 1.53MHz, the line regulation at full load is 8.29mV/V, the internal noise of the circuit is low, the transient response time from on load to full load is 42ns, and the phase margin is close to 80deg.
A Survey on Low-Power Design of VLSI Circuits

WANG Guanjun,ZHOU Yong,ZHAO Ying,WANG Maoli

IF: 1.992

2011-01-01

Microelectronics Journal

Abstract:With the revolutionary progress in semiconductor industry and upgrading IC performance,power consumption of IC is increasing dramatically.Low power design becomes the only way to solve this problem.Recent development and progress in low power design,power estimation and optimization approaches,power optimization tools,and low power test were discussed in detail,in order to provide some valuable reference for related research and design.
Design of Low-power Portable Multi-function Digital Oscilloscope

Xueli Zhou,Yuke Tian,Jie Shi,Na Zhao,Yu Yang

DOI: https://doi.org/10.1109/imcec51613.2021.9482318

2021-06-18

Abstract:With the continuous development of integrated circuit technology and digital processing technology, this article designed a portable low-power multifunction digital oscilloscope based on STM32F407ZGT6. The input signal can be processed through the signal conditioning circuit, and the ADC module carried by the main control chip STM32 is used to collect external signals, using a 3.5-inch TFT-LCD to display the processed signal waveform. The added touch screen makes the operation more convenient. The software ported the UCOS-II embedded operating system and the graphical support system UCGUI in embedded applications to form a complete real-time operating system. After actual testing, the oscilloscope has the characteristics of high real-time performance, low power consumption, stable and practical performance. And it has strong practical value and promotion value.

Programme Design of Reference Voltage Source Module Embedded in LCOS Chip

Novel design of reference voltage source integrated in LCoS chip

Design of reference voltage source integrated in LCoS chip

Design of the Power Management Module Integrated in SOC

A Novel Fully On-Chip CMOS Low-Dropout Linear Regulator with Ultra Low Noise

A Low-Power Voltage Reference Source for Lithium Battery Protection ICs

Design of Low Parasitic Inductance SiC MOSFETs Halfbridge Power Modules

Design Methodology Of Cmos Low Power

Design of Area-Efficient GHz Range Current Mode Frequency Synthesizer Using Standard CMOS Technology

Design of Voltage–Current Reference Source in CMOS Technology

Power Supply Module Design in the Low Power Consumption Application

Circuit Design of Single Panel Color LCOS Microdisplay Chip

A 30na Temperature-Independent CMOS Current Reference and Its Application in an LDO

An Inverter-based On-chip Voltage Reference Generator for Low Power Application

Research and Design of High PSR,Low power,Chip-level LDO

Low-Power Methods Research of SoC Physical Design

Layout Design and Verification of the Voltage Reference Module in the Auto Electronic Ignition Control Chip

Design and implementation of a novel programmable power monitor chip

A high-range reference voltage low-dropout regulation design for voltage-controlled oscillator circuit

A Survey on Low-Power Design of VLSI Circuits

Design of Low-power Portable Multi-function Digital Oscilloscope