Abstract:Highlights • The convection in the Cu pattern surface increase with the Cu layer thickness. • The mechanism of Cu layer improvement under high current density was explained. • The adsorption model of the convection-dependent additives during the high current density Cu pattern electroplating process was proposed. • The Cu pattern with excellent properties was electroplated under a current density of 8 ASD with an ultra-high rate of over 90 μm/h. Background Cu pattern electroplating plays an essential role in the interconnection and microstructure fabrication of high-power device packaging. However, improving efficiency while ensuring the preparation quality is an urgent breakthrough direction. Methods A new electrolyte formula suitable for the high-rate Cu pattern electroplating was put forward, including 300 mg/L polyethylene glycol (PEG, molecular weight=8000) and 6 mg/L thiazolinyl polydipropyl sulfonate (SH110). The mechanism of high-rate Cu pattern electroplating was investigated by the combination of fluid flow simulation and the electrochemical measurements including galvanostatic measurements (GMs) and cyclic voltametric (CV) tests. The Cu pattern was electroplated in the Haring-Cell with air bubble as the forced convection method. Significant findings The simulation results indicate that the flow rate on the ring-shaped cathodic pattern surface gradually increases with the Cu growing up, which also increase from the pattern surface to the bulk electrolyte. The GMs results suggest that the cathodic polarization of the convection-dependent additives raises with the current density, which is strengthened by strong convection with current density lower than 6 ASD but have the opposite effect with current density larger than 8 ASD. The CV tests indicating that the aggregation of weak convection and strong polarization promote the antagonistic effect between thiolate of SH110 and PEG, the nucleation and the electroplating rate. Nevertheless, the synergistic effect of thiazoline of SH110 and PEG are enhanced with strong convection and weak polarization. The adsorption model during the Cu pattern electroplating process is established and verified by electroplating experiment with the optimum current density of 8 ASD. The Cu pattern is mirror bright with the high electroplating rate of over 90 μm/h. Graphical abstract Download : Download high-res image (160KB) Download : Download full-size image

Frequency Effect of Pulse Plating on the Uniformity of Copper Deposition in Plated Through Holes

A New Copper Electrodeposition Scheme to Reduce Void Defects after Chemical Mechanical Polishing

Plating Uniformity of Bottom-Up Copper Pillars and Patterns for Ic Substrates with Additive-Assisted Electrodeposition

Void Defect Reduction after Chemical Mechanical Planarization of Trenches Filled by Direct/Pulse Plating

Synergistic effects of additives on impurity residues in high-speed copper electrodeposition and voiding propensity in solder joints

Improved Uniformity of Conformal Through-Hole Copper Electrodeposition by Revision of Plating Cell Configuration

A transfer-adsorption model for forward understanding the synergistic effects of additives in through-hole uniform copper thickening

Electrochemical behaviors of additives in high Cu(II) concentration solution for high-aspect-ratio through ceramic holes filling

Effect of HEDP on copper electroplating from non-cyanide alkaline baths

Interactive Effects of Additives and Electrolyte Flow Rate on the Microstructure of Electrodeposited Copper Foils

Combined fluid flow simulation with electrochemical measurement for mechanism investigation of high-rate Cu pattern electroplating

Toward Ultra-High-rate Copper Pattern Electroplating with Simultaneously Improved Coating Properties Via Simulations and Experiments

Behavior of Copper Removal by CMP and Its Correlation to Deposit Structure and Impurity Content

Studies of polixetonium chloride as a novel, hypotoxic and single additive of copper electronic plating for microvia void-free filling in printed circuit board application

Influence of Convection-Dependent Adsorption of Additives on Microvia Filling by Copper Electroplating

The Study of the Stability of Pd/PVP Nanoparticles Added with Phosphoric Acid and the Activity to Electroless Cu Deposition

The influence of fluoride ion on the current efficiency of pulse plating of copper

Promotion of High-Speed Copper-Filling Performance for Interconnections with Increasing Aspect-Ratio Using Compound Additives

A Study of Primary Factors Influencing the Properties of Plating Throwing Power for Printed Circuit Boards

Recent Advances in Electroplating of Through-Hole Copper Interconnection

Pulsed Current and Potential Response of Acid Copper System with Additives and the Double Layer Effect