Abstract:Organic additives used in Cu electroplating for IC interconnects have been studied extensively due to their pivotal roles in the void-free filling of recessed features. The suppressive additives are typically polymers or co-polymers with variable molecular weight (MW). The properties of these additives, as well as their interaction with accelerator, vary with the monomer type and the MW. As the additives are typically treated as indivisible molecules in the analysis of the filling mechanism, these variations are typically quantified by the difference in some coefficients that characterize the additive behaviors, such as adsorption / desorption rates and suppression strength. As an example, polyethylene glycol (PEG) with a larger MW would have a higher adsorption rate and exhibit stronger suppression effect than PEG with a smaller MW. However, since these large molecules consist of multiple identical building blocks from the polymerization of one or more monomer species, the behavior of the molecule as a whole depends on the number and type of the monomers. In order to understand such an intrinsic dependency and the resulting differences in additive properties, stochastic modeling was applied in the study of suppressor additive and its interaction with accelerator [1]. Using PEG and SPS as the model chemicals, a stochastic model was developed to simulate the transient processes in Cu electroplating, e.g. cyclic voltammogram (CV) under various conditions. Simulations were performed for both suppressor-only cases and suppressor-accelerator interactions. The dependency of PEG adsorption / desorption and PEG-SPS interaction on various factors, including bath composition, scan rate and molecular weight, was simulated and compared with the corresponding experimental measurements. An overall good qualitative match was shown in the comparisons. Figure 1 shows simulated CVs under two very different conditions. At higher SPS/Cl - concentrations, case (a) demonstrates the PEG-SPS interaction, which has been known to be important for the super-conformal filling of trenches [2, 3]. At lower SPS / Cl - concentrations, case (b) demonstrates the critical desorption behavior of PEG as a suppressor, which has been shown to be important for the fast bottom-up type filling of high aspect ratio TSVs in damascene copper plating [4]. Since the proposed model provides a unified approach to simulate both the suppress-accelerator interaction and the critical desorption behavior of suppressors, it enables the development of general-purpose multi-scale simulation programs for the filling of various recessed features within a wide length-scale range covering both the Damascene interconnects and TSVs. References [1] L. Yang, A. Radisic, J. Deconinck, P. Vereecken, Journal of the Electrochemical Society, 161, D269(2014) [2] A. C. West, S. Mayer, J. Reid, Electrochemical and Solid-State Letters, 4, C50(2001) [3] T. P. Moffat, D. Wheeler, W. H. Huber, D. Josell, Electrochemical and Solid-State Letters, 4, C26(2001) [4] L. Yang, A. Radisic, J. Deconinck, P. Vereecken, Journal of the Electrochemical Society, 160, D3051(2013) Figure 1

Combined fluid flow simulation with electrochemical measurement for mechanism investigation of high-rate Cu pattern electroplating

Toward Ultra-High-rate Copper Pattern Electroplating with Simultaneously Improved Coating Properties Via Simulations and Experiments

Electrochemical Analysis of Cathode in TSV Copper Electroplating

Electrochemical behaviors of additives in high Cu(II) concentration solution for high-aspect-ratio through ceramic holes filling

Interactive Effects of Additives and Electrolyte Flow Rate on the Microstructure of Electrodeposited Copper Foils

Plating Uniformity of Bottom-Up Copper Pillars and Patterns for Ic Substrates with Additive-Assisted Electrodeposition

Effects of Additive on the Electrodeposition and Coating Structure in a Novel System of Electronic Copper Electroplating

Application of Fluid Simulation in High-Speed Copper Sulfate Plating Using a Jet Flow Device

Influence Mechanism of Synergistic Additives on the Nucleation and Coating Morphology and Structure of Copper Electronic Plating

Stochastic Modeling of Organic Additives in Cu Electroplating

Electrodeposition of Copper with Ultra-large Grains and Good Conductivity

Self-organized Periodic Pattern Dynamics of Porous Copper Electrodeposition at the Industrial Large Current

Electroless Plating Cycle Process for High-Conductivity Flexible Printed Circuits

Effects of Fe(III) and Cu(I) on Electrodeposition and Microstructure Characterization for Acid Plating Bath

Electroless Copper Plating in the Presence of THPED and EDTA·2Na as the Dual-Chelating Agent

A comparison of typical additives for copper electroplating based on theoretical computation

Copper Electroplating with Polyethylene Glycol: Part II. Experimental Analysis and Determination of Model Parameters

Development of high copper concentration, low operating temperature, and environmentally friendly electroless copper plating using a copper ‐ glycerin complex solution

A transfer-adsorption model for forward understanding the synergistic effects of additives in through-hole uniform copper thickening

Electroless Copper Plating Process of N, N, N′, N′-tetrakis (2-Hydroxypropyl) Ethylenediamine System with High Plating Rate

Flow Field Simulation Assisted Investigation of Aspect Ratio on Transformation Mechanism of Micro Through Holes Cu Electroplating Performance