Abstract:Highlights • The convection in the Cu pattern surface increase with the Cu layer thickness. • The mechanism of Cu layer improvement under high current density was explained. • The adsorption model of the convection-dependent additives during the high current density Cu pattern electroplating process was proposed. • The Cu pattern with excellent properties was electroplated under a current density of 8 ASD with an ultra-high rate of over 90 μm/h. Background Cu pattern electroplating plays an essential role in the interconnection and microstructure fabrication of high-power device packaging. However, improving efficiency while ensuring the preparation quality is an urgent breakthrough direction. Methods A new electrolyte formula suitable for the high-rate Cu pattern electroplating was put forward, including 300 mg/L polyethylene glycol (PEG, molecular weight=8000) and 6 mg/L thiazolinyl polydipropyl sulfonate (SH110). The mechanism of high-rate Cu pattern electroplating was investigated by the combination of fluid flow simulation and the electrochemical measurements including galvanostatic measurements (GMs) and cyclic voltametric (CV) tests. The Cu pattern was electroplated in the Haring-Cell with air bubble as the forced convection method. Significant findings The simulation results indicate that the flow rate on the ring-shaped cathodic pattern surface gradually increases with the Cu growing up, which also increase from the pattern surface to the bulk electrolyte. The GMs results suggest that the cathodic polarization of the convection-dependent additives raises with the current density, which is strengthened by strong convection with current density lower than 6 ASD but have the opposite effect with current density larger than 8 ASD. The CV tests indicating that the aggregation of weak convection and strong polarization promote the antagonistic effect between thiolate of SH110 and PEG, the nucleation and the electroplating rate. Nevertheless, the synergistic effect of thiazoline of SH110 and PEG are enhanced with strong convection and weak polarization. The adsorption model during the Cu pattern electroplating process is established and verified by electroplating experiment with the optimum current density of 8 ASD. The Cu pattern is mirror bright with the high electroplating rate of over 90 μm/h. Graphical abstract Download : Download high-res image (160KB) Download : Download full-size image

Computational and experiments exploration of convection on Cu filling characteristics of multiple aspect-ratio micro through-holes

Study on the behaviors of Cu filling in special through-silicon-vias by the simulation of electric field distribution

Influence of Electroplating Current Density on Through Silicon Via Filling

Modeling the Bottom-Up Filling of Through Silicon Vias with Different Additives

Modeling the Copper Electrodeposition of Through-silicon-vias Corresponded to Linear Sweep Voltammetry

A Numerical Model for Bottom-Up Copper Electrodeposition of TSV with Additives

Simulation of TSV Copper Electrodeposition Process with Additives

Promotion of High-Speed Copper-Filling Performance for Interconnections with Increasing Aspect-Ratio Using Compound Additives

Electrochemical behaviors of additives in high Cu(II) concentration solution for high-aspect-ratio through ceramic holes filling

Very High Aspect Ratio (AR>10) through Glass Hole (TGH) Filling in Stagnant Condition By Using DC Plating for Advanced Interposer Applications

Simulation of copper electroplating fill process of through silicon via

Simulating the Influence of Supporting Electrolyte Concentration on Copper Electrodeposition in Microvias

Combined fluid flow simulation with electrochemical measurement for mechanism investigation of high-rate Cu pattern electroplating

Density Maximization of One-Step Electrodeposited Copper Nanocones and Dropwise Condensation Heat-Transfer Performance Evaluation

Simultaneous filling of through silicon vias (TSVs) with different aspect ratios using multi-step direct current density

Understanding Effect of Additives in Copper Electroplating Filling for Through Silicon Via

Simulation of through via bottom-up copper plating with accelerator for the filling of TSVs

FEA study on the TSV copper filling influenced by the additives and electroplating process

A transfer-adsorption model for forward understanding the synergistic effects of additives in through-hole uniform copper thickening

Effect of additives on copper electroplating profile for TSV filling

Optimization of Cu electrodeposition parameters for Through Silicon Via (TSV)