Abstract:Cu matrix composites have received increased attention in a wide industrial area because of their excellent mechanical properties and good electrical and thermal conductivity. However, the addition of general ceramic reinforcements often leads to a marked reduction in electrical conductivity for Cu matrix composites. In this study, the ZrB 2 -reinforced Cu composites have been developed to overcome this drawback since these metal borides possess relatively high electrical conductivity. The 5 wt.% ZrB 2 /Cu composites were prepared using hot-pressed sintering techniques at varying temperatures from 760 to 920°C. The influence of sintering temperature on the microstructure, relative density, and mechanical and electrical properties was examined. The results of the SEM observation show that ZrB 2 particles are seamlessly integrated into the Cu matrix for all ZrB 2 /Cu composites. The average grain size of the Cu matrix increases from 360 to 980 nm with the increase of the sintering temperature. The increase in sintering temperature also leads to the surface porosity decrease from 1.4 to 0.4%. The relative density and electric conductivity of the composites increase at the same time as the sintering temperature increases. However, microhardness increases and decreases, with a maximum value of 92 HV0.2 achieved at 840°C. The elastic modulus and nanohardness maps determined from the nanoindentation indicate that the reinforced ZrB 2 particles demonstrate the highest values for elastic modulus (340–500 GPa) and nanohardness (30–48 GPa). At the same time, the Cu matrix possesses a modulus of 100–200 GPa and nanohardness of about 10 GPa. TEM observation confirmed that the sintering temperature exhibits little influence on the interface reaction between ZrB 2 and Cu. Both sharp interface and interface with amorphous transition layer are observed. The variation of microhardness is mainly due to the strengthening of grain refinement and to the mismatch of the thermal expansion coefficients. The above results can provide further insights into the deeper understanding of the role of sintering temperature during hot-pressed sintering.

Studies of ZrO2/Cu Nanocomposites Prepared by in Situ Chemical Route

Microstructure and Properties of In-Situ TiC Reinforced Copper Nanocomposites Fabricated Via Long-Term Ball Milling and Hot Pressing

In Situ Formation of Cu–ZrO2 Composites by Chemical Routes

Effect of alloying element Zr on microstructure and properties of Cu−Y2O3 composites

Microstructure and properties of Y2O3/Cu composites fabricated by a novel liquid phase in situ reactive synthesis process

Microstructure and mechanical properties of nano-carbon reinforced Mo–Cu–Zr composites

Preparation and properties of ZrB 2-Cu composites by spark plasma sintering

Effect of Sintering Temperature on the Microstructure and Properties of High-Strength and Highly Conductive 5 wt.% ZrB2/Cu Composite

Microstructure and Wear Resistance of Cu/nano-SiC Composite

Precipitation behavior and mechanical properties of Al-Zn-Mg-Cu matrix nanocomposites: Effects of SiC nanoparticles addition and heat treatment

Fabrication and Properties of Nano-TiCx/Cu-Cr-Zr Alloy Composites

Study on toughening effect of zirconia nanocomposites

A comprehensive study of Al-Cu-Mg system reinforced with nano-ZrO2 particles synthesized by powder metallurgy technique

Preparation and Mechanical Properties of Fine Grain Al2O3-ZrO2 Composite Ceramics

Study of Effect of Zr Addition on the Microstructures and Mechanical Properties of (ticx–tib2)/cu Composites by Combustion Synthesis and Hot Press Consolidation in the Cu–Ti–B4C–Zr System

Microstructure and mechanical properties of Zn based composites reinforced by Ti3AlC2

Abrasive Wear and Physical Properties of In-Situ Nano-TiCx Reinforced Cu–Cr–Zr Composites

Preparation and Electrical Characterization of Carbon Nanotube /zro2composite Ceramics

Spark plasma sintering and mechanical properties of Al_2O_3-ZrO_2 nanocomposites

Reinforcing and Toughening Alumina/titania Ceramic Composites with Nano-Dopants from Nanostructured Composite Powders

The Effect Of Zro2 Nanoparticles On The Microstructure And Properties Of Sintered Wc-Bronze-Based Diamond Composites