Abstract:Grain refinement of Zr–containing Al alloys has attracted extensive attention for many years in both industry and academia, since "Zr–poisoning" phenomenon always happens when commercial refiner is applied in such alloys. This unrecoverable grain nucleating obstacle finally leads to poor grain refinement efficiency. In this work, a special Al–Ti–C master alloy rich in TiC nano–particles was applied to a high–strength Al–Zn–Mg–Cu–Zr alloy (i.e. 7050 alloy). The effects of TiC nano–particles on the microstructure and mechanical properties of 7050 alloy during solidification, hot extrusion and subsequent heat treatment were systematically investigated. The results show that prominent grain refinement occurs with TiC addition through both the growth restriction effect and heterogeneous nucleation. Meanwhile, TiC nano–particles are more inclined to distribute along grain boundaries than the interior of matrix grains after solidification. After subsequent homogenization and hot extrusion, TiC nano–particles tend to align along extrusion direction. In comparison with 7050 matrix alloy, the tensile properties especially ductility of 1% TiCp/7050 composite after heat treatment have been improved obviously. Furthermore, it is worth noting that precipitates in the composite have also been obviously refined. Synergetic effects of grain refinement, refined precipitates and increased dislocation density are responsible for the optimized mechanical properties of TiCp/7050 composite. This work provides new insights for controlling matrix grains of Zr–containing Al alloys and developing low–cost Al matrix composites.

Fabrication and Properties of Nano-TiCx/Cu-Cr-Zr Alloy Composites

Microstructure and Properties of In-Situ TiC Reinforced Copper Nanocomposites Fabricated Via Long-Term Ball Milling and Hot Pressing

Grain Refinement and Mechanical Properties of Cu-Cr-Zr Alloys with Different Nano-Sized TiCp Addition.

Abrasive Wear and Physical Properties of In-Situ Nano-TiCx Reinforced Cu–Cr–Zr Composites

Tuning composition and microstructure by doping Ti and C for enhancing mechanical property and wear resistance of Al0.2Co1.5CrFeNi1.5Ti0.5 high entropy alloy matrix composites

Investigation on microstructure and properties of TiC0.5-Al2O3/Cu composites fabricated by a novel in-situ reactive synthesis

Ni composites reinforced with ultrafine and uniform TiCx and Cr3C2 particles in situ: Enhanced properties and a well-matched interface

Preparation of in situ TiC@TiN core–shell and Ti2N–Al4C3 nanoparticles and their effects on Al–Zn–Mg–Cu alloy

Controlling the sizes of in-situ TiC nanoparticles for high-performance TiC/Al–Cu nanocomposites

Wear-Resistant TiC Strengthening CoCrNi-Based High-Entropy Alloy Composite

Fabrication, microstructure and mechanical properties of TiAl matrix composite reinforced by submicro/nano-Ti 2 AlC

Microstructure, mechanical properties and strengthening mechanism of in-situ synthesized TiC/6061 nanocomposites

Compression Properties and Electrical Conductivity of In-Situ 20 vol.% Nano-Sized TiC x /Cu Composites with Different Particle Size and Morphology.

Microstructure and compression behavior of in-situ synthesized Ti2AlC reinforced Ti-48Al-2Cr alloy with carbon nanotubes addition

Novel TiC-based composites with enhanced mechanical properties

Enhanced grain refinement and mechanical properties of a high–strength Al–Zn–Mg–Cu–Zr alloy induced by TiC nano–particles

Optimization of the mechanical properties of CNTs/Cu composite by regulating the size of interfacial TiC

Synthesis and Mechanical Properties of Nano-Layered Composite

Fabrication and characterization of W/Cu/Ni-based high specific gravity alloy with Zr and Ti combined addition

Preparation and Characterization of In Situ (TiC-TiB2)/Al-Cu-Mg-Si Composites with High Strength and Wear Resistance

Microstructure and mechanical properties of aluminum alloy composites with endogenous nano-TiCp