Abstract:Microstructural development and nanoscale compositional variations in mechanically alloyed Fe2O3-SnO2 powders have been examined by transmission electron microscopy and energy dispersive X-ray spectrometry. The mean grain size was found to stabilize around 10 nm after 19 h milling time, in close agreement with that estimated from X-ray diffraction line broadening measurements, whereas dissolution of SnO2 grains was incomplete even after 110 h. Isolated grains with the SnO2 cassiterite structure, of diameter >10 nm, persisted up to the maximum milling time. These observations are discussed in relation to previous measurements in the same system by X-ray diffraction and Mossbauer spectroscopy, which suggested that alloying on the atomic scale occurred after 110 h milling. The present studies confirm that the amount of Sn dissolved in the Fe2O3 hematite lattice increases with longer milling times, indicating that a supersaturated solid solution is formed, but that mixing may be locally inhomogeneous at the atomic level. Similar conclusions have been reported for studies of mechanical alloying in immiscible metallic systems. The, tendency for SnO2 grains above a certain critical size to remain undissolved, while smaller grains can more easily enter into solid solution with Fe2O3, is consistent with the expected behaviour due to the increased chemical contribution to the interfacial energy with decreasing grain size. Mossbauer results also showed that some of the SnO2 had not reacted with Fe2O3 after 110 h milling.

Microstructure and gas sensitive properties of α(M: Sn and Ti) materials prepared by ball milling

Microstructure and Electromagnetic Properties of Fe-Si-Al Flakes Produced from Melt-Spun Ribbons

Characterization of Nanostructured Alpha-Fe2o3-Sno2 Solid Solutions Prepared by High Energy Ball Milling

Gas-sensitive Properties and Structure of Nanostructured ( - Materials Prepared by Mechanical Alloying

Interstitial Positions Of Tin Ions In Alpha-(Ferichsn)(2)O-3 Solid Solutions Prepared By Mechanical Alloying

Microstructure and Melting Behavior of Tin Nanoparticles Embedded in Alumina Matrix Processed by Ball Milling

Effect of ball-milling on the phase structure and hydrogen storage properties of Ti0.9Zr0.1Mn1.5 alloy

Preparations and Electrochemical Properties of Amorphous Ti-Al Alloys

Interstitial Positions of Tin Ions in Α-(Ferichsn)2

Correlation of Gas Sensitive Properties with Fe2O3-SnO2 Ceramic Microstructure Prepared by High Energy Ball Milling

Transmission Electron Microscopy Studies of Mechanical Alloying in the Immiscible Fe2o3-Sno2 System

Microstructure and Mechanical Properties and Corrosion Behavior of Ti-Mo-Sn Alloys

The evolution of microstructure and magnetic properties of Fe–Si–Al powders prepared through melt-spinning

Melting point depression of tin nanoparticles embedded in a stable alpha-alumina matrix fabricated by ball milling

Nanocrystalline Oxides and Sulphides Prepared by Hydrothermal Processing and Mechanical Milling

Magnetic and Microstructural Properties of Nanostructured/Amorphous NiTi Prepared by Mechanical Alloying

Microstructure and Properties of A Tial Alloy Prepared by Mechanical Milling and Subsequent Reactive Sintering

Microstructure Characterization of the Cu-Ti-C Composites Prepared by Mechanical Alloying and Spark Plasma Sintering

Microstructural Characterization of Cold-Sprayed Nanostructured FeAl Intermetallic Compound Coating and Its Ball-Milled Feedstock Powders

Structural and thermal properties of the Fe-based alloys prepared by mechanical milling

Effect of Mechanical Alloying on Microstructure and Mechanical Properties of Ti-24Nb-4Zr-3Mn Alloys Prepared by Spark Plasma Sintering