Abstract:Tin oxide nanocrystals, both pure and Cu2+ and Fe3+ doped, have been prepared by a sol–gel process. The response of these materials to carbon monoxide in dry air has been investigated as a function of annealing temperature. The growth of the crystallites was monitored by XRPD from room temperature to about 900 °C and the response of the material to CO was studied for materials annealed over that temperature range. All of the materials were shown to respond to low concentrations of CO with a narrow peak in sensitivity at an operating temperature of about 200 °C. A good response to CO was also observed at an operating temperature of about 400 °C. No improvements in selectivity to CO were observed by the addition of either of the cation dopants. The sensitivity to CO was shown to decrease as crystallite size increased. The addition of the metal cation dopants impeded crystallite growth. Our previously reported Cu K-edge and Fe K-edge EXAFS measurements, on the Cu2+ and Fe3+ doped materials respectively, showed the dopant cations to move from ordered Sn4+ substitutional lattice sites in the as-prepared materials to more disordered regions, most likely the surface regions, as the materials were annealed. This dopant migration begins at about 400 °C and is accompanied by a corresponding large decrease in response to CO at an operating temperature of about 200 °C (the peak in sensitivity). This is attributed to the migration of the dopants to the surface of the crystallites and speculative explanations are given. The reduction in response of the same materials at an operating temperature of about 400 °C is not so large, indicating the response mechanisms at 200 and 400 °C to be different.

Gas-sensitive Properties and Structure of Nanostructured ( - Materials Prepared by Mechanical Alloying

Microstructure and gas sensitive properties of α(M: Sn and Ti) materials prepared by ball milling

Correlation of Gas Sensitive Properties with Fe2O3-SnO2 Ceramic Microstructure Prepared by High Energy Ball Milling

Fabrication and Gas Sensing Properties of Hollow Core–shell SnO2/α-Fe2O3 Heterogeneous Structures

Gas Sensing Property and Microstructure of SnO2 Nanocrystalline Prepared by Solid State Reaction—thermal Oxidation

Improved Sensitivity of α-Fe2O3 Nanoparticle-Decorated ZnO Nanowire Gas Sensor for CO

Characterization of Nanostructured Α-Fe2o3-sno2 Solid Solutions Prepared by High Energy Ball Milling

Interstitial Positions Of Tin Ions In Alpha-(Ferichsn)(2)O-3 Solid Solutions Prepared By Mechanical Alloying

The effect of Al addition on the gas sensing properties of Fe2O3-based sensors

Enhanced Triethylamine Sensing Performance of Α-Fe2o3 Nanoparticle/zno Nanorod Heterostructures

Surface Enhancement Effects of Tiny SnO2 Nanoparticle Modification on Α-Fe2o3 for Room-Temperature NH3 Sensing.

Gas Sensing Characteristics of Nano-Structured Metal Oxides

Preparation and gas-sensitive properties of hollow Zn2SnO4/SnO2 nano-cubes

Surface Enhancement Effects of Tiny SnO 2 Nanoparticle Modification on α-Fe 2 O 3 for Room-Temperature NH 3 Sensing

Gas-sensing performance of SnO2-based chemoresistive sensors after irradiation with alpha particles and gamma-rays

Particle Size Effect on Optical and Gas-Sensing Properties of La0.67Ca0.2Ba0.13Fe0.97M0.03O3 (M = Ti4+, Mn3+, and Cr3+) Compounds

High NO2 gas sensing performance of tin-dichalcogenides at room temperature via high-energy mechanical milling synthesis

Performance of 1D tin (Sn) decorated spherical shape ZnO nanostructures as an acetone gas sensor for room and high temperature

Lattice expansion and oxygen vacancy of α-Fe2O3 during gas sensing

Synthesis and Gas Sensing Properties of ∝-Fe2o3 Microspheres Toward Ppb-Level Aniline Detection

The effects of crystallite growth and dopant migration on the carbon monoxide sensing characteristics of nanocrystalline tin oxide based sensor materials