Abstract:To enhance the efficiency of cathode electron injection of organic light-emitting diode (OLEDs), we designed a new hybrid modified layer (HML) with the structure of Bphen: LiF/Al/MoO3, which was applied to ITO/NPB/Alq(3)/Al. The traditional material LiF is used for the electron injection layer of the reference device. The results show that using HBL at the interface between organic and cathode is very effective. We have measured the electroluminescence (EL) spectra of the device. The EL peak of the device is 534 nm, which indicates that it is from Alga. It can be seen that the structure design of the multilayer modified layer does not change the luminescence spectrum of the device. Bright green emission can be obtained from the optimized EL devices. Compared with traditional device based on LiF, the performance of the single unit with hybrid modification layer has better luminous properties and efficiency. Present research work shows that when the optimum parameter of the hybrid layer is Bphen LiF(5 nm; 6%)/Al(1nm)/MoO3(5 nm), the maximum current efficiency and the maximum power efficiency of the device are 4. 28 cd.A(-1) and 2. 19 lm.W-1, respectively, which are 25. 5% and 23. 7% higher than those of the reference device. Current-voltage characteristics demonstrate that the hybrid interfacial layer can promote electron injection, thus increasing the current efficiency and reduced their operating voltage slightly of OLED. We systematically analyze the improvement of device performance from two aspects. On the one hand, LiF can fill the electron trap of Bphen to enhance the current injection, moreover, HML can also block hole transport and reduce the hole current. On the other hand, based on charge balance factor theory, HML enhances the injection of electrons and increases the charge balance factor, which improves the balance of carriers in the device. The experimental results show that the cathode hybrid layer can improve the performance of the device.

Enhanced Electron Injection in Organic Light-Emitting Devices by Using a Composite Electron Injection Layer Composed of 8-Hydroquinolatolithium and Cesium Oxide

Enhancement of Electron Injection in Organic Light-Emitting Devices Using an Ag/LiF Cathode

Cesium Hydroxide Doped Tris-(8-Hydroxyquinoline) Aluminum As an Effective Electron Injection Layer in Inverted Bottom-Emission Organic Light Emitting Diodes

Enhanced Brightness of Organic Light-Emitting Diodes Based on Mg:Ag Cathode Using Alkali Metal Chlorides As an Electron Injection Layer

Enhanced Properties of Organic Electroluminescent Devices with Cesium Chloride Ultra-Thin Layer

Lead(Iv) Dioxide: an Effective Electron Injection Material to Realize High-Efficiency Inverted Top-Emitting Organic Light-Emitting Diodes

Enhanced Brightness and Efficiency in Organic Light-Emitting Devices Using an Lif-Doped Electron-Injecting Layer with Aluminium Cathode

Efficient inverted organic light-emitting devices using a charge-generation unit as electron-injection layers

Organic Cesium Salt As an Efficient Electron Injection Material for Organic Light-Emitting Diodes

Novel Cs2co3:Ag/Ag Cathode for High-Efficiency Organic Light-Emitting Diodes

Highly efficient and stable electron injection layer for inverted organic light-emitting diodes

Investigation of Novel Efficient Electron Injection Lithium Complex Containing Quinoxaline Moiety for Organic Light-Emitting Diodes

Improving Electron Injection and Microcavity Effect for Constructing Highly Efficient Inverted Top-Emitting Organic Light-Emitting Diode

Organic LED Based on a Novel Cohost Electron Transport Layer

Novel Solution-Processed ZnO-Based Electron Injection Layer for Organic Light-Emitting Diodes

Efficient Organic Light-Emitting Diode Using Lithium Tetra(8-Hydroxy-Quinolinato) Boron As the Electron Injection Layer

Effect of the CsCl Buffer Layer on the Performances of the Organic Electro-Luminescent Devices

Lithium Cobalt Oxide As Electron Injection Material for High Performance Organic Light-Emitting Diodes

P-113: Novel Structure Organic Light-Emitting Diodes with High Performance

Enhanced Hole Injection and Improved Performance in Organic Light-Emitting Devices by Utilizing a Novel Composite Hole Injection Layer

Improved Performance with a Hybrid Cathodic Interfacial Layer in OLEDs