Abstract:NiCr-based self-lubricating PM304 coatings have been used successfully in many high-temperature, high-speed applications such as air cycle machines, bleed air turbo compressors and turbo expanders. However, coarse PM304 coatings are not fully dense, containing a few percentages of pores and cracks which are harmful not only to the coating's tribological properties but also to the coating's overall mechanical strength. Furthermore, fine IS304 was prepared by the methods of high energy ball milling and induction sintering. The size of self-lubricating phase was refined, with Ag particles of about 5 mu m and BaF2/CaF2 of about 1 mu M. The results show that temperature and microstructure have a great effect on wear properties of IS304 and PM304 coatings. At the temperature of 20-340 degrees C, the friction coefficients of two types of coatings (IS304 and PM304) are higher, and the microscopic brittle fracture is the dominant wear mechanism. With the increase of the temperature, the coefficient of the coatings decreases rapidly due to the formation of self-lubricating film on the worn surfaces which consist of Ag and fluoride. At the temperature of 340-700 degrees C, since the self lubricating phase is fine and uniformly distributed in the IS304 coatings, it makes the formation of an intact lubricating film as well as Ag film fine and well distributed. Thus, the friction coefficient of IS304 is lower than that of PM304. With a further increase at the temperature of 700-800 degrees C, there is the plastic flow on the surfaces of the softened self-lubricating film under the influence of the friction force. Consequently, the friction coefficients of the coatings increase obviously. Comparing the PM304 with IS304 coatings, as the size of Ag film is large and the plastic flow of Ag film is much more severe than that of fluoride film, the friction coefficient of PM304 is higher than that of IS304.

PM304 coating on a Ni-based superalloy by PM technique

Pm304 Coating on A Ni-Based Superalloy Rod for High Temperature Lubrication

A NiCr-BASED HIGH TEMPERATURE SELF LUBRICATING COATING PM304 PREPARED BY POWDER METALLURGY

Microstructure and Characteristics of Rapid Sintered Low Friction, Wear Resistant 80Ni20cr–cr2o3–ag–baf2/caf2coating

Fabrication and performance of Ni-Co-P/Si3N4 electroplated composite coatings on al-si alloys

Microstructure and tribological properties of Ni-based self-lubricating coating

PREPARATION AND PROPERTIES OF HIGH TEMPERATURE SELF LUBRICATING COATINGS BY INDUCTION SINTERING

Synthesis and Tensile Binding Strength of Ni-Based Self-Lubricating Coatings

Microstructure and Tensile Strength of Pm304 Composite

Aluminide Coating Prepared on Ni-Base Superalloy by Pack Cementation

Correlation between microstructure and mechanical properties of novel Co-Ni-based powder metallurgy superalloy

Deposition of NiAl/Al3Ni2(CrB2) Coatings from Ni, Al and CrB2 Powders Using Mechanical Synthesis in Planetary Ball Mill

Tribological Property of Self-Lubricating PM304 Composite

Tribological Property Of High Temperature-Resistant Self Lubricating Pm304 Composite

The Effect of Coating Grain Size on the Selective Oxidation Behaviour of Ni-Cr-Al Alloy

A Magnetron Sputtered Microcrystalline Β-Nial Coating for SC Superalloys. Part II. Effects of a NiCrO Diffusion Barrier on Oxidation Behavior at 1100 °C

Effects of aluminised-coating on microstructure and properties of Ni–Co-base superalloys

Fabrication and Characterization of NiCoCrAlY Coating Deposited on Nickel-Based Superalloy Substrates

Investigation of Microstructural Stability and Tensile Deformation Behavior of a Novel PM Ni-based Superalloy During Long-Term Thermal Exposure

Microstructures and oxidation behavior of PM Ni-based superalloy FGH97 with in-situ carbide precipitates

High-temperature Tribological Properties of a Novel AlFeCoNiCr-Cr3C2 Cermet Coatings