Abstract:Precursor infiltration and pyrolysis (PIP) and chemical vapor infiltration (CVI) were used to fabricate SiC/SiC composites on a four-step 3D SiC fibre preform deposited with a pyrolytic carbon interface. The effects of fabrication processes on the microstructure and mechanical properties of the SiC/SiC composites were studied. Results showed the presence of irregular cracks in the matrix of the SiC/SiC composites prepared through PIP, and the crystal structure was amorphous. The room temperature flexural strength and modulus were 873.62 MPa and 98.16 GPa, respectively. The matrix of the SiC/SiC composites prepared through CVI was tightly bonded without cracks, the crystal structure had high crystallinity, and the room temperature bending strength and modulus were 790.79 MPa and 150.32 GPa, respectively. After heat treatment at 1300 degrees C for 50 h, the flexural strength and modulus retention rate of the SiC/SiC composites prepared through PIP were 50.01% and 61.87%, and those of the composites prepared through CVI were 99.24% and 96.18%, respectively. The mechanism of the evolution of the mechanical properties after heat treatment was examined, and the analysis revealed that it was caused by the different fabrication processes of the SiC matrix. After heat treatment, the SiC crystallites prepared through PIP greatly increased, and the SiOxCy in the matrix decomposed to produce volatile gases SiO and/or CO, ultimately leading to an increase in the number of cracks and porosity in the material and a decrease in the material load-bearing capacity. However, the size of the SiC crystallites prepared through CVI hardly changed, the SiC matrix was tightly bonded without cracks, and the load-bearing capacity only slightly changed.

Effect of Fabrication Process of Carbon Interlayer on Mechanical Properties of SiC_f/SiC Composites

Mechanical Behavior of SiCf/SiC Composites with Alternating PyC/SiC Multilayer Interphases

Influence of SiC Coating Thickness on Mechanical Properties of SiCf/SiC Composite

MECHANICAL PROPERTY OF 2.5 DIMENSIONAL SILICON CARBIDE FIBER REINFORCED SILICON CARBIDE COMPOSITES

Effect of Pyrocarbon Content in C/C Preforms on Microstructure and Mechanical Properties of the C/C–SiC Composites

2.5-DIMENSION SiCf/SiC COMPOSITES FABRICATED BY LOW PRESSURE CHEMICAL VAPOR INFILTRATION

Effects of In-Situ Carbon Layer and Volume Fraction of SiC Fiber on the Mechanical Properties and Fracture Behaviors of SiCf/SiC Composites Fabricated by a Modified PIP Method

Effects of fabrication processes on the properties of SiC/SiC composites

Processing and Properties of 2D SiC/SiC Composites by Precursor Infiltration and Pyrolysis

EFFECT OF C/C POROUS PREFORM ON THE MICROSTRUCTURE AND FLEXURAL STRENGTH OF C/C-SiC COMPOSITES

Fabrication, Microstructures and Properties of SiCf/SiC Composites Prepared with Two Kinds of SiC Fibers As Reinforcements

Fabrication of SiCf/SiO2 Composites and the Influence of Interfaces on the Mechanical Properties

Effects of the Single Layer Cvd Sic Interphases on the Mechanical Properties of the Sicf/Sic Composites Fabricated by Pip Process

Mechanical Properties and Fracture Behaviors of C/C Composites with PyC/TaC/PyC, PyC/SiC/TaC/PyC Multi-Interlayers

The Effect of PyC/SiC Compound Interphase on the Properties of PIP SiC/SiC Composite

Effect of Pyc Interphase Thickness on Mechanical Behaviors of Sibc Matrix Modified C/Sic Composites Fabricated by Reactive Melt Infiltration

Microstructure and Mechanical Properties of Three-Dimensional Carbon/Silicon Carbide Composites Fabricated by Chemical Vapor Infiltration

Effects of pyrochemical treatment for producing interfacial carbon layer on tensile properties of polymer-derived-matrix-based SiC/SiC composites

Effect of Carbon Interlayer on Oxidation Behavior of C/SiC Composites with a Coating from Room Temperature to 1500°C

Effect of C/SiC Volume Ratios on Mechanical and Oxidation Behaviors of Cf/C–SiC Composites Fabricated by Chemical Vapor Infiltration Technique

Effect of Atmosphere and Interlayer Thickness on the Mechanical Properties of 3D C/PyC/SiC Composites under Cyclic Stressed and Unstressed Conditions