Abstract:Bulk glassy alloy rods with a diameter of 20mm were produced for Zr61Ti2Nb2Al7.5Ni10Cu17.5 and Zr60Ti2Nb2Al7.5Ni10Cu18.5 by a tilt casting method. The replacement of Zr by a small amount of Ti and Nb caused a distinct increase in the maximum diameter from 16 mm for Zr65Al7.5Ni10Cu17.5 to 20 mm, accompanying the decrease in liquidus temperature and the increase in reduced glass transition temperature. The primary precipitation phase from supercooled liquid also shows a distinct change, i.e., from coexistent Zr2Cu,Zr2Ni and Zr6NiAl2 phases for the 65%Zr alloy to an icosahedral phase for the 61%Zr and 60%Zr alloys. These results allow us to presume that the enhancement of the glass-forming ability is due to an increase in the stability of supercooled liquid against crystallization caused by the development of icosahedral short-range ordered atomic configurations. The 60%Zr specimens taken from the central and near-surface regions in the transverse cross section at the site which is 15 mm away from the bottom surface of the cast glassy rod with a diameter of 20 turn exhibit good mechanical properties under a compressive deformation mode, i.e., Young's modulus of 81 GPa, large elastic strain of 0.02, high yield strength of 1610 MPa and distinct plastic strain of 0.012. Besides, a number of shear bands are observed along the maximum shear stress plane on the peripheral surface near the final fracture site. The finding of producing the large scale Zr-based bulk glassy alloys exhibiting reliable mechanical properties is encouraging for future advancement of bulk glassy alloys as a new type of functional material. [doi: 10.2320/matertrans.MER2008179]

Formation, Thermal Stability and Mechanical Properties of Bulk Glassy Alloys with a Diameter of 20 Mm in Zr-(Ti,Nb)-Al-Ni-Cu System

Formation and High Mechanical Strength of Bulk Glassy Alloys in Zr-Al-Co-Cu System

Glass-Forming Ability and Mechanical Properties of Zr-Ni-Al Bulk Metallic Glasses with High Zr Content

Formation, Thermal Stability and Mechanical Properties of Zr-Nb-Cu-Ni-Al Bulk Metallic Glasses

Bulk Amorphous, Nano-Crystalline and Nano-Quasicrystalline Alloys. IV. Thermal Stability and Mechanical Strength of Bulk Glassy Ni-Nb-Ti-Zr Alloys.

Formation and mechanical properties of Zr–Ni–Al glassy alloys with high glass-forming ability

Thermophysical and Mechanical Properties of Multicomponent Zr37Hf16Ni12.5Cu12.5Al1 1co6nb5 Bulk Glass-Forming Alloy

Thermophysical and Mechanical Properties of Multicomponent Zr37Hf16Ni12.5Cu12.5Al11Co6Nb5 Bulk Glass-Forming Alloy

Formation, Thermal Stability and Mechanical Properties of (Cu0.6Zr0.3Ti0.1)100-xMx (M=Fe, Co, Ni) Bulk Glassy Alloys.

Formation, Thermal Stability, Mechanical Properties and Corrosion Resistance of Cu-Zr-Ti-Ni-Nb Bulk Glassy Alloys

Formation and Mechanical Properties of Bulk Glassy and Quasicrystalline Alloys in Zr-Al-Cu-Ti System

Glass-forming Ability and Mechanical Properties of Zr75−xNi25Alx Bulk Glassy Alloys

Formation , Thermal Stability and Mechanical Properties of ( Cu 0 . 6 Zr 0

Glass-forming ability and corrosion resistance of Zr-based Zr-Ni-Al bulk metallic glasses

Synthesis and Thermal Stability of New Ni-Based Bulk Glassy Alloy with Excellent Mechanical Properties

Formation, Thermal Stability and Mechanical Properties of Cu-Zr and Cu-Hf Binary Glassy Alloy Rods

Bulk Glassy and Quasicrystalline (Zr<SUB>65</SUB>Al<SUB>7.5</SUB>Cu<SUB>27.5</SUB>)<SUB>100&minus;<I>x</I></SUB>Ti<I><SUB>x</SUB></I> Alloys and Their Mechanical Properties

Formation and Thermal Stability of Ni-Based Bulk Metallic Glasses in Ni-Zr-Nb-Al System

Formation of Ti–Zr–Ni–Cu–Be–Nb bulk metallic glasses

New Glassy Zr-Al-Fe and Zr-Al-Co Alloys with A Large Supercooled Liquid Region

Bulk Glassy and Quasicrystalline (Zr65Al7.5Cu27.5)100−xTix Alloys and Their Mechanical Properties