Abstract:(Zr62Cu15.4Ni12.6) (x = 6–12) in situ glassy composites containing uniformly distributed Ta-rich particles were prepared by arc-melting and copper mould casting. The results show that addition of 6–10 at.% Ta to Zr62Cu15.4Ni12.6Al10 results in dissolution of 2.4 to 4.6 at.% Ta in the glassy matrix, which promotes glass-forming ability, and the remaining Ta precipitates out as body-centered cubic (BCC) Ta-rich particles dispersed on the glassy matrix. The critical diameters for the composites with 6, 8, and 10 at.% Ta are 7, 7, and 6 mm, respectively. At 12 at.% Ta addition, the glass-forming ability is dramatically reduced because of the precipitation of secondary dendritic Ta-rich particles and other nanocrystallites from melts during copper mould casting. Also, owing to the solid-liquid reaction during induction heating, some Ta-rich particles formed in the master alloys will redissolve into the glassy matrix, resulting in a smaller volume fraction of Ta-rich particles in the as-cast glassy rods than that of the corresponding ingots. The glassy matrix composites exhibit enhanced plastic strain of about 7.5 to 22.5% at room temperature. The optimum Ta content in the glassy alloys is determined to be 10 at.%, which corresponds to the highest ultimate stress of 2220 MPa and the largest plastic strain of 22.5%. The plastic strain increases with increasing volume fraction of in situ BCC Ta-rich particles. This is apparently ascribed to the impedance of Ta-rich particles to shear bands. Ta-rich particles seed the initiation of multiple shear bands and block the shear band propagation, leading to intensive multiplication and bifurcation of shear bands.

Synthesis and Thermal Stability of New Ni-Based Bulk Glassy Alloy with Excellent Mechanical Properties

Thermal Stability and Mechanical Properties of Bulk Glassy Cu-Zr-Ti-(Nb, Ta) Alloys

Formation, Thermal Stability and Mechanical Properties of Zr-Nb-Cu-Ni-Al Bulk Metallic Glasses

Synthesis,structure and Mechanical Properties of Zr-Cu-based Bulk Metallic Glass Composites

Structure and properties of Zr–Ta–Cu–Ni–Al bulk metallic glasses and metallic glass matrix composites

Glass Forming Ability and Mechanical Properties of New Ni-Based Bulk Metallic Glasses

Cu-Based Bulk Glassy Alloys with Good Mechanical Properties in Cu-Zr-Hf-Ti System

A Ti-based bulk glassy alloy with high strength and good glass forming ability

Glass-forming Ability and Crystallization Behavior of Some Binary and Ternary Ni-based Glassy Alloys

Cu-based bulk glassy alloys with high tensile strength of over 2000 MPa

Effects of Small Amount Ta on the Characteristics of the Zr-Al-Ni-Cu-Ta Bulk Metallic Glass

High-strength Cu-based bulk glassy alloys in Cu–Zr–Ti and Cu–Hf–Ti ternary systems

Thermal Stability and Mechanical Properties of Zr50Ti5Cu18Ni17Al10 Bulk Metallic Glass

Zr-Cu-Ni-Al-Ta Glassy Matrix Composites with Enhanced Plasticity

Formation and Thermal Properties of Ti-Based Bulk Amorphous Alloy

PREPARATION AND PROPERTIES OF HIGH STRENGTH BULK METALLIC GLASS Ti_(53)Cu_(15)Ni_(18.5)Al_7M_3Si_3B_(0.5) (m=zr, Hf, Sc)

Glass Formation and Mechanical Properties of Ti–Cu–Ni Alloys with High Ti Content

Glass forming ability of bulk(Zr0.6Cu0.2Ni0.1Al0.1)100-xTix amorphous alloys

Effects Of Ta, Nb And Mo Additions On Glass-Forming Ability Of Ti50ni20cu25sn5 Amorphous Alloy

Formation and Compressive Properties of A Ni-Ti-Zr-Al-Cu-Si Amorphous Alloy

Glass-forming Ability and Thermal Stability of a New Bulk Metallic Glass in the Quaternary Zr–Cu–Ni–Al System