Abstract:Mg-Y-Zn-Al alloys processed by the rapidly solidified ribbon consolidation (RSRC) technique are candidate materials for structural applications due to their improved mechanical performance. Their outstanding mechanical strength is attributed to solute-enriched stacking faults (SESFs), which can form cluster-arranged layers (CALs) and cluster-arranged nanoplates (CANaPs) or complete the long-period stacking ordered (LPSO) phase. The thermal stability of these solute arrangements strongly influences mechanical performance at elevated temperatures. In this study, an RSRC-processed Mg—0.9%, Zn—2.05%, Y—0.15% Al (at%) alloy was heated at a rate of 0.666 K/s up to 833 K, a temperature very close to melting point. During annealing, in situ X-ray diffraction (XRD) measurements were performed using synchrotron radiation in order to monitor changes in the structure. These in situ XRD experiments were completed with ex situ electron microscopy investigations before and after annealing. At 753 K and above, the ratio of the matrix lattice constants, c/a, decreased considerably, which was restored during cooling. This decrease in c/a could be attributed to partial melting in the volumes with high solute contents, causing a change in the chemical composition of the remaining solid material. In addition, the XRD intensity of the secondary phase increased at the beginning of cooling and then remained unchanged, which was attributed to a long-range ordering of the solute-enriched phase. Both the matrix grains and the solute-enriched particles were coarsened during the heat treatment, as revealed by electron microscopy.

Microstructure Evolution and Mechanical Properties of 7A09 Aluminum Alloy During Rapid Solidifications

MICROSTRUCTURE OF AS-MELT SPUN Al-Cu-Mg-Fe-Ni ALLOY AND ITS VARIATION IN CONTINUOUS HEAT TREATMENT

Microstructure Evolution and Properties of Mg-9Gd-0.8Al Alloy with Lamellar Phase During Extrusion at Different Temperatures

Gradient Microstructure and Multiple Mechanical Properties of AlSi9Cu Alloy Ribbon Produced by Melt Spinning

Effects of Solidification Rates on Microstructure Refinement and Elemental Distribution of Ti44Al6Nb1.0Cr2.0V0.1B0.15Y Alloy by Rapid Solidification

On the Effect of the Melt Cooling Rate upon Spinning on the Structure of the Surface Layers of Fe77Ni1Si9B13 Alloy Ribbons

Effects Of Rolling Process On Microstructure And Mechanical Property Of 7050 Aluminum Alloy

Effect of Cooling Rate on Solidification Parameters and Microstructure of Al-7Si-0.3Mg-0.15Fe Alloy

Microstructural Evolution and Mechanical Properties of Pure Aluminum upon Multi-Pass Caliber Rolling

Microstructure, Mechanical and Tribological Properties of the Rapidly Solidified NiAl/Cr(Mo,Dy) Hypoeutectic Alloy

The Microstructure of As-Melt Spun Al–7%Si–0.3%Mg Alloy and Its Variation in Continuous Heat Treatment

Microstructure and Mechanical Properties of Al-Si Alloys Produced by Rapid Solidification and Hot Extrusion

Effect of cooling rate on microstructure and mechanical properties of Mg-9Gd-4Y-1Zn-1Al alloy

Annealing Behavior of a Mg-Y-Zn-Al Alloy Processed by Rapidly Solidified Ribbon Consolidation

Studies on the New Technique of Rapid Solidification and the Mechanical Behaviors of Mocrocrystalline Alloys

Microstructure evolution, mechanical response, and corrosion resistance for a 2195 Al-Li alloy under different rolling reductions during cryorolling

Transient Spinodal Decomposition During Annealing of Rapidly Solidified Al-10Sr Alloy

Effects of the cooling rate on mechanical properties and microstructure of near- α Ti-6Al-3Zr-2Nb-Mo alloy

Microstructure Evolution of the Near-Surface Deformed Layer and Corrosion Behavior of Hot Rolled AA7050 Aluminum Alloy

Microstructure, Biocorrosion And Cytotoxicity Evaluations Of Rapid Solidified Mg-3ca Alloy Ribbons As A Biodegradable Material

Recrystallization behavior and texture evolution during annealing of cryogenic-rolled 3003 aluminum alloy