Abstract:The Ni-Mn-based shape memory alloys as a promising candidate of elastocaloric material has been reported in many literatures, especially on bulk samples. The as-spun ribbon, which has a larger surface area and is more efficient for heat transfer, is rarely studied and hence of importance. In the present work, we succeeded in producing very long as-spun Ni-Fe-Mn-(Al, In) ribbons, with around 300 mm in length. The microstructure and mechanical properties of these as-spun ribbons were thoroughly investigated by scanning electron microscopy / electron backscattered diffraction (SEM/EBSD), nanoindentation and 3-points bending experiments. Through SEM/EBSD analyses, the microstructure and texture of the as-spun ribbons were studied. A gradient in microstructure exists along the thickness direction (TD) of the ribbon, which is induced by the temperature gradient during fast rate solidification, resulting in fine equiaxed grains along the surface contacted with the rotating wheel in melt spinning process and elongated grains, respectively. Both equiaxed and elongated grains possess a strong {001} fiber texture (<001>//TD). Nanoindentation analyses show little variation of hardness between the two different microstructures. The ductility index of both Ni-Fe-Mn-Al and Ni-Fe-Mn-In ribbons are within the range of intermetallic materials. The substitution of In by Al allows to increase very slightly the ductility index, which can reach 0.75. The fine equiaxed grains show better tensile resistance than the elongated grains in 3-points bending test. The substitution of In by Al improves the maximum bending strain by a factor of 3. The maximum strain for Ni-Fe-Mn-Al as-spun ribbons can reach 3 % before fracture. Fractography shows that the intergranular fracture is the main damage mechanism in these as-spun ribbons.

On the Effect of the Melt Cooling Rate upon Spinning on the Structure of the Surface Layers of Fe77Ni1Si9B13 Alloy Ribbons

MICROSTRUCTURE OF AS-MELT SPUN Al-Cu-Mg-Fe-Ni ALLOY AND ITS VARIATION IN CONTINUOUS HEAT TREATMENT

Structure and Crystal Growth in Melt-Spun Fe81Ga19 Alloys

The Crystallization Kinetics Study of Finemet-Co Amorphous Alloys

Crystallization Kinetics of Co-Finemet Amorphous Alloys and Magnetic Properties of Nanocrystalline Powder Cores

Nanocrystallization Kinetics of Amorphous Fe73.5Cu1Nb3−xMoxSi13.5B9 (x=1, 2, 3) Alloys

Effect of V Substitution for Nb on the Crystallization Kinetics of FINEMET Amorphous Alloys

Crystallization Kinetics and Magnetic Properties of Fe73.5si13.5b9cu1nb1v2 Nanocrystalline Powder Cores

Revealing the effects of melt temperature on structure and magnetic properties in Fe–Si–B–C alloy

Air Surface Crystallization with Quenched-in Fe Crystallites and Associated Magnetomechanical Properties in Fe–Si–B Amorphous Ribbons

Crystallization kinetics and magnetic properties of Fe 63.5Co10Si13.5B9Cu 1Nb3 nanocrystalline powder cores

Texture of nanocomposite Nd2Fe14B/alpha-Fe melt spun ribbons

Texture of Nanocomposite Nd2Fe14B/α-Fe Melt Spun Ribbons

Gradient Microstructure and Multiple Mechanical Properties of AlSi9Cu Alloy Ribbon Produced by Melt Spinning

Effect of melt-spinning speed on the microstructure and magnetic properties of Al–Cu–Fe alloy-doped SmCo5 ribbons

Microstructure and correlated mechanical properties study of Ni-(Fe, Co)-Mn-(Al, In) as-spun ribbons

Structural and Magnetic Evolution of Rapidly Quenched Sm-Fe-Si-C Alloys

Research on Phases and Morphology of Sm<sub>2</sub>Fe<sub>17</sub> Melt-Spun Ribbon

Microstructure and crystallization of melt-spun Ti–Ni–Zr–Y alloys

Microstructure of Mg-Al-Zn Based Alloy Thick Ribbons Prepared by Melt Spinning

An investigation on the microstructural stability of rapidly solidified AlFeVSi alloy ribbon