Abstract:This study aimed to enhance the sinterability and conductivity of yttria fully stabilized zirconia electrolyte through co-doping by 2 mol% of ZnO and different contents of MnO 2 (0, 0.5, 1, 1.5 mol%) at two sintering temperatures of 1300 and 1400 °C. Phase composition identification, density, microstructure, and conductivity of the samples were evaluated using X-ray diffraction (XRD), Archimedes' method, field emission scanning electron microscopy (FESEM), and electrochemical impedance spectroscopy (EIS), respectively. The XRD results revealed that ZnO and MnO 2 are successfully doped in the fluorite structure of YSZ sintered at 1400 °C, and the cubic structure is completely preserved. However, at a sintering temperature of 1300 °C, the (111) peaks of doped samples were slightly split, which implied a slight phase transformation of YSZ from cubic to a tetragonal structure. The co-doped samples, at both sintering temperatures, showed higher relative density and grain size compared with pure YSZ. The addition of 2 mol% of ZnO and 0.5 mol% of MnO 2 at 1400 °C increased the relative density of YSZ from 81.6% to 95.1%. The increase in relative density and grain size, while maintaining the cubic structure, caused an increase in the conductivity of the mentioned sample. Compared with pure YSZ, the sample's total conductivity increased from 7.37 to 10.03 S m −1 at 800 °C. The proposed composition showed better sintering behavior, lower activation energy of grain conductivity, and higher conductivity than pure YSZ. This behavior is thought to be due to the facilitating rearrangement of atoms during sintering and an increase in oxygen ion vacancy concentration due to co-doping with the appropriate amount of ZnO and MnO 2 .

Electrical Properties of Thin-Walled 8 Mol% Yttria-Stabilized Zirconia Electrolyte Tubes Prepared by an Improved Slip Casting Method

Electrical Properties and Applications of （zro2）0.92 （Y2O3）0.08 Electrolyte Thin Wall Tubes Prepared by Improved Slip Casting Method

Sintering and Electrical Properties of YSZ Electrolyte Tubes with Thin Wall Prepared by an Improved Slip Casting

Cubic Yttria Stabilized Zirconia Sintering Additive Impacts: A Comparative Study

Characterization of YSZ electrolyte membrane tubes prepared by a vacuum casting method

Study on Preparation and Properties of YSZ Electrolyte Membrane Tubes with Low Cost

Study on the properties of YSZ electrolyte fabricated by plaster casting method

The Propertied Of Ysz Electrolyte Sintering At 1300 Degrees Enc

Preparation of Tubular YSZ Electrolyte and Its Application in Solid Oxide Fuel Cells

Fabrication and Properties of Porous Yttria-Stabilized Zirconia Ceramics

Influence of Thickness on the Electrical Conductivity of YSZ Electrolytes

Preparation of YSZ Electrolyte Membrane Tube by Vacuum Casting and Its Application to Solid Oxide Fuel Cells

The Properties of YSZ Electrolyte Sintering at 1300 °C

Improvement of Mechanical Strength of 8 mol % Yttria-Stabilized Zirconia Ceramics by Spark-Plasma Sintering

Study on the Properties of Ysz Electrolyte Made by Plaster Casting Method and the Applications in Solid Oxide Fuel Cells

Nano-dispersed yttria-stabilized zirconia powder: Phase, morphology, and conductivity investigation with different chelating agents via a modified sol-gel method

Enhancing sintering behavior and conductivity of YSZ electrolyte by co-doping of ZnO and MnO 2

Effect Of Bismuth Oxide On The Microstructure And Electrical Conductivity Of Yttria Stabilized Zirconia

Properties of YSZ Electrolyte Sintered at 1250°C

Influence of Microstructure on the Ionic Conductivity of Plasma-Sprayed Yttria-Stabilized Zirconia Deposits

Microstructure Development of Plasma-Sprayed Yttria-Stabilized Zirconia and Its Effect on Electrical Conductivity