Abstract:The AlN/BN composite ceramic, fabricated via hot-press sintering, exhibits obvious anisotropy due to the establishment of directional alignment of h-BN. However, the variation and influence mechanisms of bending strength (σ) and thermal conductivity (λ) are remain unclear in different directions, which greatly limit the application of AlN/BN composite ceramics. In this paper, the effects of h-BN content on phase composition, microstructure and anisotropy of AlN/BN composite ceramics are discussed in detail. The results reveal that AlN/BN composite ceramics have three directions: perpendicular (⊥), longitudinal parallel (∥), and lateral parallel (≡) to the hot-pressing direction. The content of h-BN is a crucial factor affecting the anisotropy of AlN/BN composite ceramics. h-BN enhances the thermal conductivity in the ∥ and hinders the thermal conductivity in the ⊥. With the increase in h-BN amount, λ∥ rises gradually, while λ⊥ gradually falls. When the mass percentage of h-BN and AlN is 25 % (AB25), the λ∥ is as high as 90 W m−1 K−1, which is about 2.25 times that of λ⊥. In terms of mechanical properties, σ ≡ and σ ⊥ first increase and then decrease, while σ ∥ only decreases. This is attributable to h-BN being effective in enhancing mechanical properties by inhibiting crack propagation in the ⊥ and ≡ direction, while the promotion of crack propagation leads to a decrease in mechanical properties in the ∥ direction. σ ≡ reaches the highest values (σ ≡ = 460.2 MPa) at an h-BN amount of 10 % (AB10), which is about 1.19 and 2.04 times that of σ ⊥ and σ ∥, respectively, and 22.1 % higher than that of AB0.

Effect of hexagonal BN on the microstructure and mechanical properties of Si3N4 ceramics

Effect of Hexagonal BN on the Microstructure and Mechanical Properties of Pressureless Sintered Porous Si3N4 Ceramics

Fracture Behavior and Toughness of H-Bn/si_3n_4 Ceramic Composites

Fabrication and Mechanical Properties of Boron Nitride Nanotube Reinforced Silicon Nitride Ceramics

Microstructure and room/elevated-temperature mechanical properties of hot-pressed h-BN composite ceramics with La2O3-Al2O3-SiO2 addition

Boron Nitride Doped Transparent Polycrystalline Silicon Nitride Ceramics

Influence of hBN content on mechanical and tribological properties of Si3N4/BN ceramic composites

Influence of titanium diboride on the microstructure and mechanical properties of silicon nitride ceramic

MICROSTRUCTURE, MECHANICAL PROPERTIES AND FRICTION/WEAR BEHAVIOR OF HOT-PRESSED Si₃N₄/ BN CERAMIC COMPOSITES

Effects of h-BN addition on microstructures and mechanical properties of β-CaSiO3 bioceramics

Properties of H-Bn/si<sub>3</sub>n<sub>4</sub> Composite Ceramics Fabricated by Gel-Casting

Mechanical and wear properties of h-BN/Si3N4 ceramic composites

Properties of h-Bn/Si<sub>3</sub>N<sub>4</sub> Composite Ceramics Fabricated by Gel-Casting

Effects of BN on the microstructural evolution and mechanical properties of BAS-BN composites

Effect of hexagonal boron nitride content on the anisotropy of hot-press-sintered AlN/BN composite ceramics

Microstructural evolution of h-BN matrix composite ceramics with La-Al-Si-O glass phase during hot-pressed sintering

Effects of AlN Content on Phase Composition, Microstructure and Mechanical Properties of BN-based Composite Ceramics

Microstructure of hot-pressed h-BN/Si3N4 ceramic composites with Y2O3–Al2O3 sintering additive

Investigation of Fabrication and Properties of Machinable Si3N4/BN Nanocomposite Ceramics

Microstructural Evolution and Mechanical Properties of H-Bn Composite Ceramics with Y 2 O 3 –aln Addition by Liquid-Phase Sintering