Abstract:The performance of welded Ni-based superalloys at high temperatures is essential to be evaluated due to their particular service environment for aero-engines and high-speed aircrafts. The tensile properties and related microstructural evolutions such as the carbide precipitate and grain of a laser-welded Ni-based alloy were experimentally and numerically investigated at different temperatures (20, 300, 500, 800 °C). The results show that at room temperature, the strength of the Base Material (BM) was slightly smaller, with a difference of less than 1%, than the Welded Material (WM), which can be attributed to the more uniformly distributed needle-shaped carbide precipitates in the WM than those nonuniformly coarser spherical ones in the BM. While at 300 °C and 500 °C, the strength of WM decreased more obviously compared with that of BM due to the more apparent growth of grain: 13.52% loss in yield strength in WM alloys as compared with BM alloys at 300 °C, and 16.57% at 500 °C. At 800 °C, the strength of BM and WM both decreased to a similar level due to Dynamic Recrystallization (DRX). However, a much higher elongation was observed for the BM than WM (less than 50% of BM), which can be attributed to the enhanced dislocation accumulation capability of the large spherical carbides along grain boundaries on the fracture surface in BM. Furthermore, a unified model considering the welding effects on both microstructures (dislocation, carbides, and grain) and mechanical properties evolutions at different temperatures was developed and validated. Based on this model, the key temperature ranges (20–600 °C) where apparent weakening of strength and uniform plasticity occurs for welded structures were identified, providing a direct guidance for potential structure and process design.

Experimental and Numerical Study of Wrought Inconel 718 Under Thermal Cycles of Variable Amplitude Coupled with Mechanical Loading

Experimental and Numerical Simulations of ELM-like Transient Damage Behaviors to Different Grade Tungsten and Tungsten Alloys

Use of Instrumented Micro-Indentation to Study the Mesoscopic Elasto-Plastic Behavior of Gh4145/Sq Superalloy During High-Temperature Cyclic Straining

High‐Temperature Mechanical Behavior Assessment based on a Developed Constitutive Model of Inconel 718 Fabricated by Selective Laser Melting

A unified material model for multiaxial ductile fracture and extremely low cycle fatigue of Inconel 718

Cyclic Plasticity Modeling of Nickel-Based Superalloy Inconel 718 under Multi-Axial Thermo-Mechanical Fatigue Loading Conditions

Crystal Plasticity Modeling and Analysis for the Transition from Intergranular to Transgranular Failure in Nickel-based Alloy Inconel 740H at Elevated Temperature

Experimental and Numerical Investigation of High-Temperature Multi-Axial Fatigue

Tensile and Low‐Cycle Fatigue Behavior of Laser Powder Bed Fused Inconel 718 at Room‐ and High Temperature

Effect of process optimization on laser additive manufacturing of Inconel 718 alloy based on finite element analysis: Thermal and structural evaluation

Microstructure and mechanical properties at elevated temperatures of as-built and heat-treated Inconel 718 produced through laser powder bed fusion processes

Wear mechanism, subsurface structure and nanomechanical properties of additive manufactured Inconel nickel (IN718) alloy

Influence of heat treatments on plastic flow of laser deposited Inconel 718: Testing and microstructural based constitutive modeling

Influence of Heat Treatment on Cyclic Response of Nickel-Based Superalloy Inconel 718 up to Very-High Cycle Regime

Anisotropic damage evolution and modeling for a nickel-based superalloy built by additive manufacturing

Cyclic microstructure analysis, crack propagation and life prediction of Inconel 750H considering the slip fracture energy

Thermodynamic Investigation with Synergetic Method on Inner Crack Growth Behavior at Very High Cycle Fatigue Regime

Experimental investigation of process parameter variations on the microstructure and failure behavior of IN718 structures in PBF-LB/M

Experiments and modeling of microstructural and mechanical behaviors of laser-welded Ni-based superalloy at high temperatures

A Damage Evolution Model Based on Micro-Structural Characteristics for an Additive Manufactured Superalloy under Monotonic and Cyclic Loading Conditions

Very-High-Cycle Fatigue Behavior of Inconel 718 Alloy Fabricated by Selective Laser Melting at Elevated Temperature