Abstract:The purpose of this paper is to investigate the influence of non-uniform precipitate distribution on local plastic deformation in HIPed P/M nickel-base superalloy FGH96 by using micro-indentation methods. The micro-indentation tests were conducted in the indenter load range from 100mN to 450mN and the loading rate range from 1.94mN/s to 19.37mN/s at the room temperature. Then, the load–displacement data of precipitate concentration areas (PCA) and precipitate sparsity areas (PSA) were obtained, respectively. The results show that both PCA and PSA exhibited decreasing micro-hardness during indentations, which proved that the size effect was significant in P/M nickel-base superalloy FGH96 as well. The high micro-hardness of PCA indicates that γ′ precipitate could effectively improve the resistance to deformation. In contrast, the influences of indenter load and loading rate on Young’s modulus were slight. Through plotting test data, it was revealed that a better linear relationship existed between H2 and 1/h. Moreover, the densities of geometrically necessary dislocations (GNDs) and statistically stored dislocations (SSDs) were obtained by data fitting. Like other alloys, the GND density fast decreased with the increase of indentation depth during indentations. The SSD density of PCA was higher than that of PSA when the loading rate was lower than 12.91mN/s, indicating that the γ′ precipitates could block the dislocation movements and induce strong interactions. However, this mechanism was inconspicuous at high loading rates due to precipitation shearing mechanism. In addition, the FEM method and forward analysis algorithms were used to predict the micro-indentation parameters. Comparing with FEM method, the prediction results were more accurate for forward analysis algorithms. The constitutive equations of PCA and PSA were established by means of reverse analysis algorithms. The microstructural simulation reflected that the interactions between PCA and PSA were significant during uniaxial compression. The high stress concentration existing in PCA between two adjacent PSAs may cause microcracks and void dislocations at the large deformations.

Use of Instrumented Micro-Indentation to Study the Mesoscopic Elasto-Plastic Behavior of Gh4145/Sq Superalloy During High-Temperature Cyclic Straining

Investigation of fatigue mesoscopic mechanical properties of a nickel-based superalloy by instrumented microindentation measurements

A Study of Fatigue Mesoscopic Elasto-Plastic Properties of a Nickel-Base Superalloy by Instrumented Microindentation Measurements

Effect of cyclic straining at elevated-temperature on static mechanical properties, microstructures and fracture behavior of nickel-based superalloy GH4145/SQ

Low cycle fatigue behavior of nickel-based superalloy GH4145/SQ at elevated temperature

An Investigation of the Effect of High-Temperature Cyclic Straining and Creep Loading on Tensile Mechanical Properties of GH4145/SQ Alloy

Investigation of fatigue mechanical properties of apolycrystalline solid at mesoscopic scale using depth-sensing indentation (DSI) technique

Determination of fatigue mesoscopic mechanical properties of an austenitic stainless steel using depth-sensing indentation (DSI) technique

Depth-Sensing Indentation-Based Studies of Surface Mechanical Behavior and Fatigue Damage Evolution of an Austenitic Stainless Steel Subjected to Cyclic Straining

Use of instrumented indentation testing to study local mechanical properties of 304L SS welded joints subjected to low-cycle fatigue loadings

Mechanical Properties of Micro-phases Along < 001 > Direction of Directionally Solidified Nickel-base Super-alloy by In-situ Nano-Indentation

High-temperature low cycle fatigue behavior of nickel based superalloy GH536

Tensile and low cycle fatigue properties of nickel-base powder metallurgy superalloy FGH95

High Temperature Low-Cycle Fatigue, Deformation Microstructure and Final Fracture Behavior of a Nickel-Base Superalloy

In-situ Study of Microstructure and Mechanical Properties of GH3536 Alloy Manufactured by Selective Laser Melting at 750 °C

Micro Mechanical Property Investigations of Ni-based High-Temperature Alloy GH4169 Based on Nanoindentation and CPFE Simulation

Investigations of inhomogeneous mechanical properties and plastic deformations in HIPed P/M nickel-base superalloy FGH96 by using micro-indentation methods

Micromechanical Behavior of Single-Crystal Superalloy with Different Crystal Orientations by Microindentation

Characterization of the Elasto-Plastic Properties of 0cr12mn5ni4mo3al Steel by Microindentation

Multiaxial fatigue behavior for superalloy GH4169 at high temperature

Constitutive Modeling and Parameter Identification of Mechanical Behavior for GH4169 Alloy at High Temperature