Abstract:To achieve high-performance nickel-based superalloys by laser metal deposition (LMD) technology for applications in aeroengines, we prepared Inconel 718 superalloys by LMD with three groups of process parameters and then heat treated them by two different protocols. We carried out compressive experiments for these Inconel 718 samples over a wide range of strain rate (0.001-5000/s) to evaluate the effects of process parameters and heat treatments on their microstructures and dynamic mechanical properties. We observed both the initial microstructures and the failure characteristics of the samples using the optical microscope and the scanning electron microscope. We found that a higher energy input density during laser additive manufacturing led to a wider range of primary dendrite spacing. The plastic flow stress of the alloy decreased near-linearly with increase in primary dendrite spacing. The anisotropy of the compressive properties of the sample resulted from the anisotropy of the as-deposited and the direct aged structures, while the microstructural and mechanical anisotropy almost vanished after full heat treatment. We further carried out compressive experiments over a wide range of strain rate (0.001-5300/s) and temperature (298-1193 K) to understand the mechanical properties of Inconel 718 by LMD in an extremely high-strain rate and high-temperature loading environment. We noticed an anomalous high-temperature peak in the flow stress, in the flow stress vs. temperature relation, under different strain rates, and we proved that it is attributed to the third type of strain aging effect. Finally, by observing the compressive failure characteristics, we found that the propagation path of a crack is dependent on the loading direction. The compressive fractography morphology could reflect the effect of heat treatment on the ductility of the samples. Furthermore, it was evident that the initial defects (gas and shrinkage porosities) in Inconel 718 samples caused by LMD can contribute to the generation, deflection, and branching of cracks.

Effect of process optimization on laser additive manufacturing of Inconel 718 alloy based on finite element analysis: Thermal and structural evaluation

Thermomechanical Process Simulation and Experimental Verification for Laser Additive Manufacturing of Inconel®718.

Impact of Pore Defects on Laser Additive Manufacturing of Inconel 718 Alloy Based on a Novel Finite Element Model: Thermal and Stress Evaluation

Establishment and experimental verification of a three-dimensional finite element model for residual stress in surface processing of Inconel 718 alloy by laser cladding

Microstructural evolution and mechanical performances of selective laser melting Inconel 718 from low to high laser power

Numerical simulation and solidification characteristics for laser cladding of Inconel 718

The effect of process parameters on the residual stress of selective laser melted Inconel 718 thin-walled part

Understanding processing parameters affecting residual stress in selective laser melting of Inconel 718 through numerical modeling

Effect of parameters on quality of IN718 parts using laser additive manufacturing

Thermomechanical process modelling and simulation for additive manufacturing of nanoparticle dispersed Inconel 718 alloys

Effect of laser cladding parameters on Inconel 718 coating performance and multi-parameter optimization

Numerical Simulation and Experimental Analysis of Thermal Conduction and Stress in Laser Cladding Repair of Thin-Walled Parts

Quantitative analysis and experimental study of the influence of process parameters on the evolution of laser cladding

Influence of Process Parameters and Heat Treatments on the Microstructures and Dynamic Mechanical Behaviors of Inconel 718 Superalloy Manufactured by Laser Metal Deposition

Numerical Simulation and Multi-Objective Parameter Optimization of Inconel718 Coating Laser Cladding

Effect of Scanning Strategy on Microstructure Evolution and Stress Control in Laser Cladding Repair of Ti6Al4V Alloy

Dendritic Microstructure and Hot Cracking of Laser Additive Manufactured Inconel 718 under Improved Base Cooling

Experimental and Statistical Analyses of Geometry Characteristics of Inconel 718 Laser Clad Layer with Response Surface Methodology

Effect of processing parameters on surface roughness, porosity and cracking of as-built IN738LC parts fabricated by laser powder bed fusion

Experimental investigation of process parameter variations on the microstructure and failure behavior of IN718 structures in PBF-LB/M

Knowledge of process-structure-property relationships to engineer better heat treatments for laser powder bed fusion additive manufactured Inconel 718