Abstract:Features peculiar to the synthesis of SiC–Si 3 N 4 –Si 2 N 2 O composite powder with a controlled content of silicon carbide, nitride, and oxynitride phases, as well as the structure and properties of hot-pressed ceramics produced from this powder, were examined. The optimal composition of the synthesized SiC–Si 3 N 4 –Si 2 N 2 O powder was achieved by heating a 1 : 3 mixture of thermally expanded graphite (TEG) and silicon up to 1200°C in air. The interaction of TEG with fine silicon at 1200°C led to the formation of a solid solution of carbon in silicon carbide, accompanied by heat release. The generated heat increased temperature within localized volumes of the TEG cellular structure to a level where air nitrogen facilitated the development of silicon nitride and oxynitride and an amorphous phase. The amorphous phase crystallized as the interaction time increased to 2.5 h. The duration of the process influenced the final distribution of the phases, formed with the participation of CO, SiO, and air nitrogen. The microstructure of the synthesized powder was characterized by a general agglomerated state, resulting from rod and plate forms of Si 3 N 4 and Si 2 N 2 O. Hot pressing of the synthesized SiC–Si 3 N 4 –Si 2 N 2 O composite powder with Al 2 O 3 and Y 2 O 3 activators yielded superfine ceramics, possessing enhanced hardness and fracture toughness (HV10 = 20.7 GPa and K Ic = 6.5 MPa · m 1/2 ). The structure of the ceramics sintered at 2000°C differed from those sintered at 1850°C, primarily by higher density and average grain size. The superfine state significantly influenced the abrasive wear resistance of the ceramics in dry friction conditions. The linear wear index of a sample with an average size of structural elements varying from 0.2 to 1.5 μm was 111 μm/km at a sliding speed of 1 m/sec under a load of 0.2 MPa. This was significantly lower than the linear wear index of industrial ceramics of reaction-sintered silicon carbide (RSSC), which was 232.4 μm/km.

Si3N4/TiN Ceramic Composites Produced by Hot Pressing

Preparation and properties of TiN–Si3N4 composites

Hot pressing and microstructural characterization of SiC and TiN added TiB2 ceramics

Synthesis and Mechanical Properties of TiB2/Ti2AlN Composites Fabricated by Hot Pressing Sintering

Fabrication of in Situ Ti 2 AlN/TiAl Composites by Reaction Hot Pressing and Their Properties

Synthesis of Si<sub>3</sub>N<sub>4</sub>-TiN-SiC Composites by Combustion Reaction under High Nitrogen Pressures

Synthesis of Si<sub>3</sub>N<sub>4</sub>-TiN-SiC Composites by Combustion Reaction under High Nitrogen Pressures

Microstructural Characteristics and Evolution of Ti2AlN/TiAl Composites with a Network Reinforcement Architecture During Reaction Hot Pressing Process

Synthesis of Si3N4–TiN–SiC Composites by Combustion Reaction under High Nitrogen Pressures

MICROSTRUCTURE AND ELECTROCONDUCTIVITY OF TiN-Al2O3 COMPOSITES PREPARED BY HOT-PRESSING

Reactive hot-pressing TiB2/AlN ceramic composites

Microstructure and mechanical properties of Ti3(Al,Ga)C2/Al2O3 composites prepared by in situ reactive hot pressing

Processing, Microstructural Characterization and Mechanical Properties of in Situ Ti3AlC2/TiAl3 Composite by Hot Pressing

Synthesis of TiN-Si3N4 Composites from Rutile and Quartz by Carbothermal Reduction Nitridation

Preparation of Si3N4–TiN–SiC composite by partial substitution of Ti–Si–Fe alloy for Si under N2 atmosphere

Preparation and Mechanical Properties of TiN-Al<sub>2</sub>O<sub>3</sub> Refractory Composites

Nano-Al2o3 Reinforced Fe-Cr-Ni Composites Fabricated by Reactive Hot Pressing

Microstructure and Mechanical Properties of TiN–TiB2–hBN Composites Fabricated by Reactive Hot Pressing Using TiN–B Mixture

Synthesis and Consolidation of Composite Materials in the SiC–Si3N4–Si2N2O System

Enhanced Performance in Si3N4 Ceramics Cutting Tool Materials by Tailoring of Phase Composition and Hot-Pressing Temperature

Si3N4/TiN Ceramic Composites Produced by Hot Pressing

Preparation and properties of TiN–Si3N4 composites

Hot pressing and microstructural characterization of SiC and TiN added TiB2 ceramics

Synthesis and Mechanical Properties of TiB2/Ti2AlN Composites Fabricated by Hot Pressing Sintering

Fabrication of in Situ Ti 2 AlN/TiAl Composites by Reaction Hot Pressing and Their Properties

Synthesis of Si&lt;sub&gt;3&lt;/sub&gt;N&lt;sub&gt;4&lt;/sub&gt;-TiN-SiC Composites by Combustion Reaction under High Nitrogen Pressures

Synthesis of Si<sub>3</sub>N<sub>4</sub>-TiN-SiC Composites by Combustion Reaction under High Nitrogen Pressures

Microstructural Characteristics and Evolution of Ti2AlN/TiAl Composites with a Network Reinforcement Architecture During Reaction Hot Pressing Process

Synthesis of Si3N4–TiN–SiC Composites by Combustion Reaction under High Nitrogen Pressures

MICROSTRUCTURE AND ELECTROCONDUCTIVITY OF TiN-Al2O3 COMPOSITES PREPARED BY HOT-PRESSING

Reactive hot-pressing TiB2/AlN ceramic composites

Microstructure and mechanical properties of Ti3(Al,Ga)C2/Al2O3 composites prepared by in situ reactive hot pressing

Processing, Microstructural Characterization and Mechanical Properties of in Situ Ti3AlC2/TiAl3 Composite by Hot Pressing

Synthesis of TiN-Si3N4 Composites from Rutile and Quartz by Carbothermal Reduction Nitridation

Preparation of Si3N4–TiN–SiC composite by partial substitution of Ti–Si–Fe alloy for Si under N2 atmosphere

Preparation and Mechanical Properties of TiN-Al&lt;sub&gt;2&lt;/sub&gt;O&lt;sub&gt;3&lt;/sub&gt; Refractory Composites

Nano-Al2o3 Reinforced Fe-Cr-Ni Composites Fabricated by Reactive Hot Pressing

Microstructure and Mechanical Properties of TiN–TiB2–hBN Composites Fabricated by Reactive Hot Pressing Using TiN–B Mixture

Synthesis and Consolidation of Composite Materials in the SiC–Si3N4–Si2N2O System

Enhanced Performance in Si3N4 Ceramics Cutting Tool Materials by Tailoring of Phase Composition and Hot-Pressing Temperature

Synthesis of Si<sub>3</sub>N<sub>4</sub>-TiN-SiC Composites by Combustion Reaction under High Nitrogen Pressures

Preparation and Mechanical Properties of TiN-Al<sub>2</sub>O<sub>3</sub> Refractory Composites