Abstract:The non-oxide-reinforced phase AlN-SiC solid solution with high performance was successfully synthesized in the resin-bonded Al-Si-SiC composites under flowing nitrogen at 1300 °C. The AlN-SiC solid solution was synthesized by three paths of liquid-solid, gas-solid and gas-gas reactions through modulation of Al/Si ratio, and controllable microstructure of AlN-SiC solid solution was attained. The phase composition and microstructure of the sintered samples were characterized by XRD and SEM, combined with thermodynamics, the formation mechanism of AlN-SiC solid solution was investigated and the reaction model was established. Al was not detected while Si was detested by XRD. Granular, short columnar and whisker-like AlN-SiC solid solution were generated and their positions varied. As the temperature increases, the partial pressure of oxygen decreases due to the oxidation of Al, Si and SiC on the surface of the sample, inside the sample, the active oxidation takes place, generating Al2O(g), SiO(g) and CO(g). Due to the low oxygen partial pressure, Al is preferentially nitrided to form a thin AlN layer on its surface. The AlN layer is broken as the temperature increases, then liquid Al with carbon from resin begins to flow, leaving the residual shell of AlN in situ. When it flows to the surface of Si, Al-Sialloy is formed locally inside the Si particles under the wetting effect of C, then hexagonal AlN-SiC solid solution is formed inside the Si shell. Part of SiO(g) + CO(g) diffuses into the interior of the AlN residual shell and reacts by aggregation to form a granular AlN-SiC solid solution in the shell wall; others diffuses into the pores of the sample for vapor deposition, and finally forms stacked hexagonal flaky whiskers. The in-situ generated of AlN-SiC solid solution with multiple morphologies in the composite plays a joint toughening effect, which can significantly enhance the comprehensive performance of the composite. In this experiment, the synthesis of AlN-SiC solid solution without sintering aids under normal pressure at a low temperature. It is expected to be applied to the blast furnace and to realize the longevity of blast furnace.

Preparation of Si3N4–TiN–SiC composite by partial substitution of Ti–Si–Fe alloy for Si under N2 atmosphere

Optimization of Microstructure to Improve Si3n4 Ceramics with Thermal Conductivity and Mechanical Properties: Effect of Si and Α-Si3n4 Powder Composition

Synthesis of Si<sub>3</sub>N<sub>4</sub>-TiN-SiC Composites by Combustion Reaction under High Nitrogen Pressures

Synthesis of Si3N4–TiN–SiC Composites by Combustion Reaction under High Nitrogen Pressures

Catalytic Nitridation Preparation of High-Performance Si3N4(w)-SiC Composite Using Fe2O3 Nano-Particle Catalyst: Experimental and DFT Studies

Synthesis of Si<sub>3</sub>N<sub>4</sub>-TiN-SiC Composites by Combustion Reaction under High Nitrogen Pressures

Preparation and properties of TiN–Si3N4 composites

Synthesis of TiN-Si3N4 Composites from Rutile and Quartz by Carbothermal Reduction Nitridation

Effect of Ti-Si-Fe alloy on the nitriding behavior of Si powder

Synthesis mechanism of AlN–SiC solid solution reinforced Al2O3 composite by two-step nitriding of Al–Si3N4–Al2O3 compact at 1500 °C

Nitridation Mechanism of Reaction Sintered Si3N4-SiC Composite

Improving the Microstructure of Si<sub>3</sub>N<sub>4</sub>-TiN Composites Using Ammonium Citrate to Disperse Raw TiO<sub>2</sub> Powders

Densification and Mechanical Properties of Si3N4/SiC Nanocomposite Using Si-Nitrided Si3N4 Powder

Fabrication of Fine-Grained Si 3 N 4 -Si 2 N 2 O Composites by Sintering Amorphous Nano-Sized Silicon Nitride Powders

Formation mechanism of AlN-SiC solid solution with multiple morphologies in Al-Si-SiC composites under flowing nitrogen at 1300 °C

The influence of Ti: Si3N4 ratio on the microstructure evolution of Ti–Si3N4 reaction in Cu melts

Addition of Si3N4 Strengthens SiC Coatings via Heat Treatment with Nitrogen Gas onto Carbon/Carbon Composites

Study on the Combustion Synthesis of Si3N4-SiC-TiN Ceramics

Improving the Microstructure of Si3N4-TiN Composites Using Ammonium Citrate to Disperse Raw TiO2 Powders

Effect of Fe‐Contained Species on the Preparation of Α‐si3n4 Fibers in Combustion Synthesis

Fabrication and Mechanical Properties of Si3N4/SiC Nanocompoisites under Pressureless Sintering.

Preparation of Si3N4–TiN–SiC composite by partial substitution of Ti–Si–Fe alloy for Si under N2 atmosphere

Optimization of Microstructure to Improve Si3n4 Ceramics with Thermal Conductivity and Mechanical Properties: Effect of Si and Α-Si3n4 Powder Composition

Synthesis of Si&lt;sub&gt;3&lt;/sub&gt;N&lt;sub&gt;4&lt;/sub&gt;-TiN-SiC Composites by Combustion Reaction under High Nitrogen Pressures

Synthesis of Si3N4–TiN–SiC Composites by Combustion Reaction under High Nitrogen Pressures

Catalytic Nitridation Preparation of High-Performance Si3N4(w)-SiC Composite Using Fe2O3 Nano-Particle Catalyst: Experimental and DFT Studies

Synthesis of Si<sub>3</sub>N<sub>4</sub>-TiN-SiC Composites by Combustion Reaction under High Nitrogen Pressures

Preparation and properties of TiN–Si3N4 composites

Synthesis of TiN-Si3N4 Composites from Rutile and Quartz by Carbothermal Reduction Nitridation

Effect of Ti-Si-Fe alloy on the nitriding behavior of Si powder

Synthesis mechanism of AlN–SiC solid solution reinforced Al2O3 composite by two-step nitriding of Al–Si3N4–Al2O3 compact at 1500 °C

Nitridation Mechanism of Reaction Sintered Si3N4-SiC Composite

Improving the Microstructure of Si&lt;sub&gt;3&lt;/sub&gt;N&lt;sub&gt;4&lt;/sub&gt;-TiN Composites Using Ammonium Citrate to Disperse Raw TiO&lt;sub&gt;2&lt;/sub&gt; Powders

Densification and Mechanical Properties of Si3N4/SiC Nanocomposite Using Si-Nitrided Si3N4 Powder

Fabrication of Fine-Grained Si 3 N 4 -Si 2 N 2 O Composites by Sintering Amorphous Nano-Sized Silicon Nitride Powders

Formation mechanism of AlN-SiC solid solution with multiple morphologies in Al-Si-SiC composites under flowing nitrogen at 1300 °C

The influence of Ti: Si3N4 ratio on the microstructure evolution of Ti–Si3N4 reaction in Cu melts

Addition of Si3N4 Strengthens SiC Coatings via Heat Treatment with Nitrogen Gas onto Carbon/Carbon Composites

Study on the Combustion Synthesis of Si3N4-SiC-TiN Ceramics

Improving the Microstructure of Si3N4-TiN Composites Using Ammonium Citrate to Disperse Raw TiO2 Powders

Effect of Fe‐Contained Species on the Preparation of Α‐si3n4 Fibers in Combustion Synthesis

Fabrication and Mechanical Properties of Si3N4/SiC Nanocompoisites under Pressureless Sintering.

Synthesis of Si<sub>3</sub>N<sub>4</sub>-TiN-SiC Composites by Combustion Reaction under High Nitrogen Pressures

Improving the Microstructure of Si<sub>3</sub>N<sub>4</sub>-TiN Composites Using Ammonium Citrate to Disperse Raw TiO<sub>2</sub> Powders