Abstract:The effect of nitrogen content on the formation of an equiaxed solidification structure of Fe-16Cr steel was investigated. Moreover, two different kinds of refractory materials, i.e., alumina and magnesia, were employed to control the type of oxide inclusion. The characteristics of TiN(-oxide) inclusions were quantitatively analyzed in both molten steel and solidified samples. When the melting was carried out in the alumina refractory, the grain size continuously decreased with increasing nitrogen content. However, a minimum grain size was observed at a specific nitrogen content (approx. 150 ppm) when the steel was melted in the magnesia refractory. Most of the single TiN particles had a cuboidal shape and fine irregularly shaped particles were located along the grain boundary due to the microsegregation of Ti at the grain boundary during solidification. The type of TiN-oxide hybrid inclusion was strongly affected by the refractory material where Al2O3-TiN and MgAl2O4-TiN hybrid-type inclusions were obtained in the alumina and magnesia refractory experiments, respectively. The formation of oxide inclusions was well predicted by thermochemical computations and it was commonly found that oxide particles were initially formed, followed by the nucleation and growth of TiN. When the nitrogen content increased, the number density of TiN linearly increased in the alumina refractory experiments. However, the number of TiN exhibits a maximum at about [N] = 150 ppm, at which a minimum grain size was obtained in the magnesia refractory experiments. Therefore, the larger the number density of TiN, the smaller the primary grain size after solidification. The number density of TiN in the steel melted in the magnesia refractory was greater than that in the steel melted in the alumina refractory at given Ti and N contents, which was due to the lower planar lattice disregistry of MgAl2O4-TiN interface rather than that of Al2O3-TiN interface. When ∆TTiN (= difference between the TiN precipitation temperature and the liquidus of the steel) was 20 K to 40 K, the number density of effective TiN was maximized and thus, the grain size was minimized after solidification. Finally, although most of the TiN particles were smaller than 1 μm in the molten steel samples irrespective of the nitrogen content, TiN particles larger than 10 μm were observed in the solidified samples when the nitrogen content was greater than 150 ppm. The growth of TiN particles during melting and solidification was well predicted by the combinatorial simulation of the ‘Ostwald ripening model’ based on the Lifshitz–Slyozov–Wagner theory in conjunction with the ‘Diffusion controlled model’ using Ohnaka’s microsegregation equation.

Effect of Ti-Si-Fe alloy on the nitriding behavior of Si powder

Optimization of Microstructure to Improve Si3n4 Ceramics with Thermal Conductivity and Mechanical Properties: Effect of Si and Α-Si3n4 Powder Composition

Preparation of Si3N4–TiN–SiC composite by partial substitution of Ti–Si–Fe alloy for Si under N2 atmosphere

The Effects of Alloying Elements Cr, Al, and Si on Oxidation Behaviors of Ni-Based Superalloys

Influence of Temperature on Phase Composition of Nitridation Products from Ferrosilicon Alloy

Effect of Sn and Si on the Synthesis of Ti<sub>3</sub>Al(Sn/Si)C<sub>2</sub> by Self-Propagating High-Temperature Sintering

Synthesis of monodisperse and high-purity α-Si3N4 powder by carbothermal reduction and nitridation

The Effects of Fe and Si Elements on Structural, Mechanical, and Electronic Properties of an Fe–Si–Ti System by First‐Principles Calculations

Catalytic Nitridation Preparation of High-Performance Si3N4(w)-SiC Composite Using Fe2O3 Nano-Particle Catalyst: Experimental and DFT Studies

The influence of Ti: Si3N4 ratio on the microstructure evolution of Ti–Si3N4 reaction in Cu melts

Effect of Si-addition on structure and thermal stability of Ti-Al-N coatings

Influence of sintering aids on the nitridation of reaction bonded Si 3N4/BN ceramics

Formation Mechanism and Effect on the Mechanical Properties of TiSi Phase for Ti-5Al-5Mo-5Cr-3Nb-2Zr Alloyed by Silicon

Effect of Fe‐Contained Species on the Preparation of Α‐si3n4 Fibers in Combustion Synthesis

In-situ Synthesis of TiN and its Effects on Fe-12Cr-6Al in Laser Powder Bed Fusion

Influence of Sintering Aids on the Nitridation of Reaction Bonded Si3n4/Bn Ceramics

Stoichiometric and Off-Stoichiometric Alloying in Silicide Compound Ti5Si3 by Nb or Cr Additions

Effect of Ni in SiO 2 coating on the oxidation resistance of TiAl alloy at 900 °C

Synergistic Effect of Nitrogen and Refractory Material on TiN Formation and Equiaxed Grain Structure of Ferritic Stainless Steel

Synthesis mechanism of α-Si3N4 whiskers via SiO vapor in reaction bonded Si3N4-SiC composite

High Temperature X-Ray Diffraction Study of the Effect of Nb and Si on Oxidation Behavior of Ti3Al Alloy