Abstract:Silva, W. C. ; Nascimento, R. M. ; Nascimento, A. B. G. ; Mendes, A. M. ; Castro, N. A. ; Silva, C. L. M. ; The demand for oil and its derivatives has driven the oil and gas sector to explore deep waters. Nickel-based alloys, like Inconel, are used due to their corrosion resistance properties. Cladding structural steels with these alloys is a cost-effective solution. However, dissimilar metal welding poses challenges, including the formation of Partially Diluted Zones (PDZ). This work highlights the use of Electron Backscatter Diffraction (EBSD) as a very adequate technique for the microstructural characterization of dissimilar anticorrosive materials. The MIG process was utilized to perform cladding of Inconel 625 onto the A36 steel substrate. The samples were prepared for analysis using techniques such as EDS, FEG-SEM, EBSD, and Vickers microhardness testing. The results demonstrate the effectiveness of the EBSD technique in characterizing dissimilar metal cladding. The combination of EBSD with EDS analysis and microhardness testing provided comprehensive insights into the microstructure and mechanical properties of the material. EDS mapping analysis confirmed the formation of PDZ with a distinct beach-like morphology, indicating localized compositional variations. The uniform thickness of the PDZ, approximately 20 μm, highlights the convective motion and solidification behavior of the partially diluted zone. Phase map EBSD analysis revealed different crystal structures in the cladding zone, including a FCC structure for the nickel cladding layer and a BCC structure for the ferritic steel base metal. The PDZ exhibited the same crystal structure as the base metal, indicating chemical element diffusion without altering the ferritic steel structure. Contrast band EBSD analysis provided detailed microstructural information, revealing solidification structures and potential hardness variations. The observed martensite formation in the PDZ highlights its susceptibility to cracking and detachment of the coated layer. The hardness results support the microstructural findings, demonstrating significant variations in hardness across the cladding structure, particularly in the PDZ and at the interface between the Inconel alloy and the base metal. These findings contribute valuable insights into the microstructural and compositional gradients within the joint region, reinforcing their implications for material performance.

Effects of the shielding gas and substrate thickness on dilution and microstructure of Inconel® 625 MIG/MAG welded coatings

Effect of the Shielding Gas and Heat Treatment in Inconel 625 Coatings Deposited by GMAW Process

Effects of welding parameters on Inconel 625 coating synthesised by tungsten inert gas cladding

Comparative study on microstructure and oxidation resistance of Inconel 625 superalloy coatings on 12CrMoV steel surfaces prepared by CMT and MIG cladding

Inconel 625 weld claddings obtained by the GMAW-RE with rotating electrode

Influence of droplet transfer behaviour on the microstructure, mechanical properties and corrosion resistance of wire arc additively manufactured Inconel (IN) 625 components

Effect of Welding Torch Mode on Heat Input, Microstructure, and Mechanical Performance of Inconel 625 via Wire‐Arc‐Directed Energy Deposition

CHARACTERIZATION OF MICRO STRUCTURAL AND MECHANICAL PROPERTIES OF INCONEL 625/A 517 HIGH STRENGTH QUENCHED AND TEMPERED STEEL DISSIMILAR WELDS

Effects of Introducing a Rotating Electrode into Arc Welding Coatings

Experimental Investigation on Single Pulse MIG Welding of Inconel 617

Microstructural evaluation and corrosion behaviour of Inconel 82 and Inconel 625 overlays on 304L stainless steel weld used in nuclear fuel reprocessing plant

Influence of inconel interlayer on microstructural, mechanical and electrochemical characteristics in single-pass ATIG welding of dissimilar austenitic and duplex stainless steel

Partially Diluted Zones in Dissimilar Cladding with AWS ER NiCrMo-3 Alloy Deposited by the MIG Process on ASTM A36 Steel: Analysis and Characterization by EBSD

In situ interlayer hot forging arc-based directed energy deposition of Inconel® 625: process development and microstructure effects

Effect of cooling strategies on Inconel 625 components produced by wire arc additive manufacturing

Studies on residual stresses and structural integrity of the dissimilar gas tungsten arc welded joint of sDSS 2507/Inconel 625 for marine application

Microstructure and sulfide stress corrosion cracking of the Inconel 625/X80 weld overlay fabricated by cold metal transfer process

Evaluation of microstructural and mechanical properties of dissimilar Inconel 625 nickel alloy–UNS S32205 duplex stainless steel weldment using MIG welding

Effect of heat treatments on Inconel 625 fabricated by wire and arc additive manufacturing: an in situ synchrotron X-ray diffraction analysis

Influence of Interlayer Temperature on Microstructure and Mechanical Properties of Additively Manufactured Inconel 625

Effect of shielding gas on MIG welding performance with austenitic wire