Abstract:This study investigates the metallurgical and mechanical properties of a nickel-based superalloy produced through wire + arc additive manufacturing (WAAM). It is a novel and fast fabrication technique based on layer-by-layer construction for rapid product development. A thin-wall component of Inconel 625 was successfully manufactured using a cold metal transfer (CMT)-based WAAM technique with an ErNiCrMo-3 wire after identifying suitable process parameters based on trial runs. The microstructure varies based on the travel and build directions, resulting in columnar, cellular, and equiaxed dendrites found in bottom, middle, and top regions. These dendritic structures evolve throughout the deposition process, predominantly influenced by temperature circumstances. The results of SEM/EDS analysis indicated that Nb and Mo segregation was lower in the interdendritic areas compared to the dendritic core areas of the thin-wall part. The XRD results discovered that the main crystal structure found in the WAAMed samples was a γ-FCC (face-centered cubic). Additionally, through EBSD analysis, the average grain size was identified as 86.45 μm in the travel direction and 89.15 μm in the build direction. The grain properties of the material were influenced by the reheating phenomenon and the circumstances of solidification that occurred throughout the layer-by-layer additive manufacturing process. The larger proportion of higher angle grain boundaries improves the mechanical properties. The average hardness in the travel direction was higher in the top (312 HV), middle (297 HV), and bottom (303 HV) sections than in the build direction (305 HV), (290 HV) and (294 HV), respectively. The mechanical properties, specifically tensile strength, exhibit anisotropy that varies depending on the direction of travel and build. The residual stress analysis shows that the as-built specimen is mainly affected by tensile stress in the travel and build directions.

Effect of cooling strategies on Inconel 625 components produced by wire arc additive manufacturing

Impact of Process Parameters on Forming Quality and Deposition Efficiency of Unsupported Rods in Wire Arc Additive Manufacturing

On the Effect of Heat Input and Interpass Temperature on the Performance of Inconel 625 Alloy Deposited Using Wire Arc Additive Manufacturing–Cold Metal Transfer Process

The Effect of Interpass Temperature on the Mechanical Properties and Microstructure of Components Made by the WAAM Method from Inconel 718 Alloy

Influence of Interlayer Temperature on Microstructure and Mechanical Properties of Additively Manufactured Inconel 625

Effect of Inter-pass Layer Temperatures on Microstructure and Mechanical Properties of Inconel 625 Fabricated Using Wire and Arc Additive Manufacturing

Influence of droplet transfer behaviour on the microstructure, mechanical properties and corrosion resistance of wire arc additively manufactured Inconel (IN) 625 components

Experimental investigation of CMT discontinuous wire arc additive manufacturing of Inconel 625

CMT-based wire arc additive manufacturing of Inconel 625 alloy

Effect of welding parameters on bead characteristics and mechanical properties of wire and arc additive manufactured inconel 718

Analysis of Heat Treatment and Its Effects on the Machinability of Inconel 718 Products Manufactured with Wire and Arc Additive Manufacturing Technique

Technology Development for Producing Inconel 625 in Aerospace Application Using Wire Arc Additive Manufacturing Process

Effects of On-Line Vortex Cooling on the Microstructure and Mechanical Properties of Wire Arc Additively Manufactured Al-Mg Alloy

Microstructure and Mechanical Properties of Thick‐Walled Inconel 625 Alloy Manufactured by Wire Arc Additive Manufacture with Different Torch Paths

Influence of Interlayer Forced Air Cooling on Microstructure and Mechanical Properties of Wire Arc Additively Manufactured 304L Austenitic Stainless Steel

Investigation of Surface Residual Stress, Mechanical Properties, and Metallurgical Characterization of Inconel 625 Multilayer Thin-Wall Component Using Cold Metal Transfer Technique

Location-dependent microstructure analysis and mechanical behavior of inconel 625 using Cold Metal Transfer(CMT) based wire and arc additive manufacturing

Grain refinement and mechanical properties improvement of Inconel 625 alloy fabricated by ultrasonic-assisted wire and arc additive manufacturing

A review on microstructure and mechanical properties of Inconel 625 alloy fabricated using wire arc additive manufacturing process

Study on Optimization Strategy for the Composition Transition Gradient in SS 316L/Inconel 625 Functionally Graded Materials

Experimental study of shielding gas concentration on mechanical properties of stainless steel alloy parts using wire and arc additive manufacturing