Abstract:Silva, W. C. ; Nascimento, R. M. ; Nascimento, A. B. G. ; Mendes, A. M. ; Castro, N. A. ; Silva, C. L. M. ; The demand for oil and its derivatives has driven the oil and gas sector to explore deep waters. Nickel-based alloys, like Inconel, are used due to their corrosion resistance properties. Cladding structural steels with these alloys is a cost-effective solution. However, dissimilar metal welding poses challenges, including the formation of Partially Diluted Zones (PDZ). This work highlights the use of Electron Backscatter Diffraction (EBSD) as a very adequate technique for the microstructural characterization of dissimilar anticorrosive materials. The MIG process was utilized to perform cladding of Inconel 625 onto the A36 steel substrate. The samples were prepared for analysis using techniques such as EDS, FEG-SEM, EBSD, and Vickers microhardness testing. The results demonstrate the effectiveness of the EBSD technique in characterizing dissimilar metal cladding. The combination of EBSD with EDS analysis and microhardness testing provided comprehensive insights into the microstructure and mechanical properties of the material. EDS mapping analysis confirmed the formation of PDZ with a distinct beach-like morphology, indicating localized compositional variations. The uniform thickness of the PDZ, approximately 20 μm, highlights the convective motion and solidification behavior of the partially diluted zone. Phase map EBSD analysis revealed different crystal structures in the cladding zone, including a FCC structure for the nickel cladding layer and a BCC structure for the ferritic steel base metal. The PDZ exhibited the same crystal structure as the base metal, indicating chemical element diffusion without altering the ferritic steel structure. Contrast band EBSD analysis provided detailed microstructural information, revealing solidification structures and potential hardness variations. The observed martensite formation in the PDZ highlights its susceptibility to cracking and detachment of the coated layer. The hardness results support the microstructural findings, demonstrating significant variations in hardness across the cladding structure, particularly in the PDZ and at the interface between the Inconel alloy and the base metal. These findings contribute valuable insights into the microstructural and compositional gradients within the joint region, reinforcing their implications for material performance.

Effects of Introducing a Rotating Electrode into Arc Welding Coatings

Effect of Arc Surface Remelting on the Corrosion Resistance of 0cr19ni9 TIG Welding Joint

Inconel 625 weld claddings obtained by the GMAW-RE with rotating electrode

Microstructural characterization and mechanical properties of high-strength steel weld metals obtained by GMAW process with rotating electrode (GMAW-RE)

Effects of the shielding gas and substrate thickness on dilution and microstructure of Inconel® 625 MIG/MAG welded coatings

Effect of the Shielding Gas and Heat Treatment in Inconel 625 Coatings Deposited by GMAW Process

Microstructural evaluation and corrosion behaviour of Inconel 82 and Inconel 625 overlays on 304L stainless steel weld used in nuclear fuel reprocessing plant

Effect of welding parameters on bead characteristics and mechanical properties of wire and arc additive manufactured inconel 718

Influence of droplet transfer behaviour on the microstructure, mechanical properties and corrosion resistance of wire arc additively manufactured Inconel (IN) 625 components

Effect of Arc Energy on the Microstructure and Electrochemical Behavior of Duplex Stainless Steel Weld Overlay Deposited by GMAW Process

Dry Sliding and Slurry Abrasion Behaviour of Wire Arc Additive Manufacturing - Cold Metal Transfer (WAAM-CMT) Cladded Inconel 625 on EN8 Steel

A comparative study on weld-bead geometry of austenitic stainless-steel produced by cold metal transfer welding and pulse metal inert gas welding process

Effect of location on microstructure and mechanical properties of additive layer manufactured Inconel 625 using gas tungsten arc welding

EFFECT OF AIR CARBON ARC GOUGING AND SUBMERGED ARC WELDING ON THE ELECTROCHEMICAL PROPERTIES OF AISI 316L AND 321 STAINLESS STEELS

Partially Diluted Zones in Dissimilar Cladding with AWS ER NiCrMo-3 Alloy Deposited by the MIG Process on ASTM A36 Steel: Analysis and Characterization by EBSD

Investigation of Single and Double Pulse Techniques on Microstructure and Mechanical Anisotropy of Inconel 686 Component Fabricated by Wire Arc Directed Energy Deposition

Effect of Welding Torch Mode on Heat Input, Microstructure, and Mechanical Performance of Inconel 625 via Wire‐Arc‐Directed Energy Deposition

Targeted influence on the weld strength of high-strength fine-grain structural steels in the GMA welding process through functionalized weld material surfaces

Effects of Oxide Powders as Activating Flux on AMIG 304L Welds

Design and Performance of Nitrogen-Alloyed Iron-Based Coating for Enhancing Galling Resistance by Plasma Transferred Arc Welding

Effects of Electrode Surface Topography on Aluminum Resistance Spot Welding