Abstract:Abstract Locally adapted properties within a machine component offer opportunities to increase the performance of a component by using high strenght materials where they are needed. The economic production of such hybrid components on the other hand represents a major challenge. The new tailored forming process chain, which is developed within the collaborative research center (CRC 1153) represents a possible solution to produce hybrid components. This is made possible by the use of pre-joined hybrid semi-finished products made from two different steel alloys, which are subsequently formed. The semi-finished products can be manufactured for example by means of deposition welding. Due to a thermal mechanical treatment, an overall higher component strength of the joining zone can be achieved. The deposition welding processes can be used to generate a cladding on a base material. During the welding, one of the most difficult tasks is to reduce the amount and size of pores in the joining zone. These pores can reduce the strength in the joining zone of the welded parts. However, additional pores can occur in the intermediate zone between the substrate and the cladding. In the presented study, the influence of the forming process on the closing of pores in the cladding and in the intermediate zone was investigated. Therefore, cylindrical specimen were extracted in longitudinal direction of the welding track by wire-cut eroding. These welding tracks are manufactured by plasma-transferred arc welding of AISI 52100 on a base plate made of AISI 1015. Further, specimens were prepared transversely, so that the base material, the intermediate layer, and the welded material are axially arranged in the specimen. The prepared specimen were checked for pores by means of scanning acoustic microscopy. Subsequently, an uniaxial compression test was carried out with various degrees of deformation and the two specimen designs were examined again for pores. A microstructure analysis was carried out after each step. The investigations show that there is a need for a minimum degree of deformation to reduce pores in the welded material. However, this required plastic strain cannot be achieved in the welded material of the hybrid specimen, which is a result of the homogeneous temperature distribution in the specimen. The homogeneous temperature distribution leads to different flow properties in the specimen, which means that the main plastic deformation is taking place in the base material.

Targeted influence on the weld strength of high-strength fine-grain structural steels in the GMA welding process through functionalized weld material surfaces

Ultrastrong and ductile steel welds achieved by fine interlocking microstructures with film-like retained austenite

Influence of Chemical Composition on the Mechanical and Microstructural Properties of High Strength Steel Weld Metals Submitted to PWHT

Thick-wire GMAW for fusion welding of high-strength steels

Influence of Metallic Oxide Nanoparticles on the Mechanical Properties of an A-TIG Welded 304L Austenitic Stainless Steel

Design and Performance of Nitrogen-Alloyed Iron-Based Coating for Enhancing Galling Resistance by Plasma Transferred Arc Welding

Microstructures from wire-fed laser welding of high strength steel grades

Influence of edge-deposited layers on mechanical and corrosion properties of laser beam welds of 15 mm thick AISI 2205 duplex stainless steel

Process-related influences and correlations in wire arc additive manufacturing of high-strength steels

High strength welding of NiTi and stainless steel by impact: Process, structure and properties

Influence of Ni and PWHT on microstructure evolution and mechanical properties of GTA-welded duplex stainless steel and super duplex stainless steel joints: A comparative investigation

Transitioning solidification mode via electroplated Ni coatings in martensitic stainless steel resistance spot welds: new insights into fabricating tough microstructure

Influence of degree of deformation on welding pore reduction in high-carbon steels

The Effect of Microstructure and Welding-Induced Plasticity on the Strength of Ni–Mo–Cr Alloy Welds

Structure and Mechanical and Technological Properties of Additive Material for Welding Heat-Resistant Steels

Use of molybdenum in Ni 620 filler metal to influence the microstructure of brazed hot work steelEinfluss von Molybdän auf das Gefüge von Ni 620 beim Löten von Warmarbeitsstahl

Undermatched Welding of Ultra-High-Strength Steel S1100 with Metal-Cored Wire: Influence of Welding Positions on Mechanical Properties

Performance optimization and investigation of metal-cored filler wires for high-strength steel during gas metal arc welding

Heat control and design-related effects on the properties and welding stresses in WAAM components of high-strength structural steels

Development in oxide metallurgy for improving the weldability of high-strength low-alloy steel—Combined deoxidizers and microalloying elements

Influence of Heat Control on Properties and Residual Stresses of Additive-Welded High-Strength Steel Components