Abstract:Nickel based superalloy (alloy 617) exhibits high strength and oxidation resistance at elevated temperatures. The major limitation of this alloy is microsegregation of alloying elements due to the formation of Molybdenum (Mo) rich secondary phases in the interdendritic region of the weldments. The present study investigates the possibilities to mitigate the microsegregation effect. In order to achieve this, weld joints were fabricated with pulsed current gas tungsten arc welding (PCGTAW) techniques with three different filler wires. The filler wires employed with present study are ERNiCrMo-4, ERNiCrMo-10 and ERNiCrMo-14. The macro examination was carried out to reveal the defects in the weld joints. Optical and Scanning electron microscope (SEM) analysis were performed to evaluate the micro structural changes in the fusion zone and Heat Affected Zone (HAZ). Microstructure shows the fine equiaxed dendrite structure in the fusion zone. Energy Dispersive x-ray Spectroscopy (EDS) analysis was also carried out in the weldments to quantify the level of microsegregation of alloying elements. Tensile test reveals the strength and ductility of the weld joints. Root and face bend test was carried out to check the ability of the weld joints to withstand bending forces. The result shows the defect free weld was achieved in all the welded joints. EDS analysis revealed the presence of Mo rich phases in the ERNiCrMo-4 filler wire. There is no evidence for the formation of secondary phases in the filler wires. The tensile strength of ERNiCrMo-14 filler shows the marginally higher strength compare to other filler wires. Root and Face bend test did not show the presence of cracks and other defects in the weldments.

Use of molybdenum in Ni 620 filler metal to influence the microstructure of brazed hot work steelEinfluss von Molybdän auf das Gefüge von Ni 620 beim Löten von Warmarbeitsstahl

Study on Ni3Al-Based Single Crystal Superalloy Joints Brazed by Vacuum Brazing with Zr-Containing Filler

Microstructural evolution and mechanical properties of Ni-based superalloy joints brazed using a ternary Ni-W-B amorphous brazing filler metal

Targeted influence on the weld strength of high-strength fine-grain structural steels in the GMA welding process through functionalized weld material surfaces

Investigations of the microstructure and mechanical properties of the Nb-Ti/Nb-Ti-Ni brazed joints

Influence of Niobium and Molybdenum on Mechanical Strength and Wear Resistance of Microalloyed Steels

Brazing Oxide Dispersion-Strengthened Fe-Based Steels with a Cu-Based Filler Metal

Effect of niobium on the mechanical strength of the laser beam welding joints of molybdenum

Intermetallic phase formation during brazing of a nickel alloy using a Ni–Cr–Si–Fe–B quinary filler alloy

Vacuum brazing SiC to Mo using Nb0.74CoCrFeNi2 eutectic high-entropy alloy filler

Effect of brazing filler alloy composition on microstructure and mechanical properties of Nb–Ti–Co/Nb–Ti joints

Microstructure Evolution and Mechanical Properties of W/MA956 Joints by Brazing

Retaining Mechanical Properties of GMA-Welded Joints of 9%Ni Steel Using Experimentally Produced Matching Ferritic Filler Metal

Microstructure evolution and improved mechanical strength of the C/C-Mo joint by adjusting the joining temperature in a wide temperature range

Synergetic effects of complex additions of Mo and Ni on the phase transformation behavior and mechanical properties of austenitic lightweight steels

Effect of Cr content in Ni-based amorphous filler on microstructure and shear strength of K4169 nickel-based alloy brazed joint

Microstructure and properties of the C/C-superalloy brazed joint by Ni-based filler

Effect of brazing temperature on the interfacial microstructure and mechanical properties of GH3039 joint brazed with electroless Ni–P filler metal

The Effect of Microstructure and Welding-Induced Plasticity on the Strength of Ni–Mo–Cr Alloy Welds

Effect of Mo on the high-temperature oxidation behavior of Cr-Ni-Mo Hot-Work Die Steels

Characterization of microstructure and mechanical properties of nickel based superalloy 617 by pulsed current gas tungsten arc welding technique