Abstract:Weld cracks and low weld strength of Nb521 to GH3128 dissimilar metal welded joint are key factors influencing their weldability. To obtain favorable crack-free laser welded joints, this research adopted copper as an interlayer to research the microstructure and properties of laser direct welded and laser offset welded joints of Nb521 to GH3128 superalloy. Compared to previous research results, the tensile strength of laser direct welded joints is enhanced by 2.5 folds. There is a melting reaction layer at the position where the center welded joints are adjacent to the Nb521 base metal, and Ni 3 Nb and Laves phases are present in the layer. The copper solid solution is located in the center of fusion zone, and Ni 3 Nb-Laves hard particles are found. The phases near the side of GH3128 superalloy base metal are Ni solid solution, Cu solid solution, Ni 3 Nb/Cr 2 Nb hard particles and high melting point alloy mixture. Macrosegregation at the laser offset welding fusion zone is more serious. The phases near the Nb521 base metal are Nb solid solution, Cu solid solution, Ni 3 Nb and Cu/Cr eutectic structure. At the center of the fusion zone, Cu solid solution, Ni 3 Nb and Cu/Cr eutectic structure are observed. The phases near GH3128 base metal are Ni solid solution, Cr 2 Nb phase and Cu solid solution. Mean Vickers hardness values of the direct welded fusion zone is 271.7 ± 129.8 HV, which reduces mismatching of hardness of the joints to a certain degree. As there are Laves phase and Ni 3 Nb brittle phase in the melting reaction layer adjacent to Nb521 base metal, the microhardness value is up to 589.1 HV. The average microhardness of the offset welded fusion zone is 449.1 ± 217.4 HV, which is higher than the hardness of Nb521 and GH3128 base metals, due to increasing number of brittle phases in the joints. Strength values of the direct welded and offset welded joints are 418.7 ± 49.8 MPa and 364.3 ± 24.5 MPa respectively, which are separately 86.0% and 74.8% of Nb521 base metal. Fractures are all found to occur at the fusion zone on the side of Nb521. The direct welded joints exhibit mixed fracture characteristics with dimples and cleavage facets on the fracture, while the offset welded joints are characterized by brittle fracture.

Effect of niobium on the mechanical strength of the laser beam welding joints of molybdenum

Microstructure, Compressive Performance and Wear Resistance of Pure Molybdenum Additively Manufactured Via Laser Powder Bed Fusion

Microstructural and mechanical properties of laser-welded molybdenum joints with the addition of nano-sized ZrC in the weld pool

Effect of adding Nb foil on joint properties of laser fusion welding for TC4 titanium and 7075 aluminum alloy

Study on Laser Overlap Welding of Titanium/Aluminum Dissimilar Metals Based on Niobium Microalloying

Investigation on dissimilar laser beam welding of molybdenum to zirconium via pure titanium interlayer

Fiber Laser Fillet Welding of Nb1Zr Thin Tube and Molybdenum End Plug in Ultra-high-Temperature Heat Pipe

Improved strength and ductility on laser beam welded joints of 7085Al matrix nanocomposites by in-situ ZrB 2 nanoparticles and Al 3 (Er, Zr) nanoprecipitates

Influences of Si-Ti combined alloying on microstructures and properties of laser welded socket joints of molybdenum

Effect of Mo on the morphology, microstructure and mechanical properties of NbTa 0.5 TiMo x refractory high entropy alloy fabricated by laser powder bed fusion using elemental mixed powders

Microstructure and mechanical properties of laser beam welding joint of in-situ (ZrB2+Al2O3)/AA7N01 nanocomposites

Dramatic improvement of the strength of laser welded joints of Nb521 to GH3128 by adding pure copper as an interlayer

New insight into microstructure and mechanical properties of heterostructures 7075 Al joint prepared via single mode laser welding

Microstructure evolution and improved mechanical strength of the C/C-Mo joint by adjusting the joining temperature in a wide temperature range

Microstructures and Mechanical Properties of Ti–24Al–17Nb (at.%) Laser Beam Welding Joints

Microstructure-Property Correlations in Fiber Laser Welded Nb-Ti Microalloyed C-Mn Steel

Influence of Cr/Mo ratio on microstructure and mechanical properties of the Ni-based superalloys fabricated by laser additive manufacturing

The Effect of Microstructure and Welding-Induced Plasticity on the Strength of Ni–Mo–Cr Alloy Welds

Effect of Molybdenum on the Impact Toughness of Heat-Affected Zone in High-Strength Low-Alloy Steel

Study on Ni3Al-Based Single Crystal Superalloy Joints Brazed by Vacuum Brazing with Zr-Containing Filler

A comparative study of the microstructure and properties of 800 MPa microalloyed C-Mn steel welded joints by laser and gas metal arc welding