Abstract:Single-crystal α-Al₂O₃ fibres can be utilized as a novel reinforcement in high-temperature composites owing to their high elastic modulus, chemical and thermal stability. Unlike non-oxide fibres and polycrystalline alumina fibres, high-temperature oxidation and polycrystalline particles boundary growth will not occur for single-crystal α-Al₂O₃ fibres. In this work, single-crystal α-Al₂O₃ whiskers and Al₂O₃ particles synergistic reinforced copper-graphite composites were fabricated by mechanical alloying and hot isostatic pressing techniques. The phase compositions, microstructures, and fracture morphologies of the composites were investigated using X-ray diffraction, a scanning electron microscope equipped with an X-ray energy-dispersive spectrometer (EDS), an electron probe microscopic analysis equipped with wavelength-dispersive spectrometer, and a transmission electron microscope equipped with EDS. The mechanical properties have been measured by a micro-hardness tester and electronic universal testing machine. The results show that the reinforcements were unevenly distributed in the matrix with the increase of their content and there were some micro-cracks located at the interface between the reinforcement and the matrix. With the increase of the Al₂O₃ whisker content, the compressive strength of the composites first increased and then decreased, while the hardness decreased. The fracture and strengthening mechanisms of the composite materials were explored on the basis of the structure and composition of the composites through the formation and function of the interface. The main strengthening mechanism in the composites was fine grain strengthening and solid solution strengthening. The fracture type of the composites was brittle fracture.

Microstructure and properties of Cu-Cr-Nb/graphite composites with high softening temperature

Microstructure and Properties of In-Situ TiC Reinforced Copper Nanocomposites Fabricated Via Long-Term Ball Milling and Hot Pressing

Influences of Ni/Cu/Cr3C2 Composite Additive on Microstructure and Properties of WC–10Co Fine Grained Hardmetal

Long-term Ball Milling and Hot Pressing of In-Situ Nanoscale Tungsten Carbides Reinforced Copper Composite and Its Characterization

Microstructure and Properties of a Graphene Reinforced Cu–Cr–Mg Composite

Effect of milling time on microstructure and mechanical properties of Cu-Ni-graphite composites

Microstructure, mechanical and tribological properties of Cu-Sn/Cr3C2/Gr composites

Improving the High Temperature Mechanical Performance of Cu-Cr Composite Induced by Residual Nano-Sized Cr Precipitates

Microstructure and High-Temperature Mechanical Properties of CrMnFeCoNi/TiAl Composites Prepared by Powder Metallurgy

Influence of Ni content on the microstructure and mechanical properties of chromium carbide-nickel composites

Investigation of the Microstructure and Mechanical Properties of Copper-Graphite Composites Reinforced with Single-Crystal α-Al2O3 Fibres by Hot Isostatic Pressing

Microstructure of Graphite and Cu-Ti-C Composites Fabricated by Mechanical Alloying and Spark Plasma Sintering

Study on the microstructure and properties of Cu-graphite-Cr3C2 composites prepared by in-situ reactive synthesis

Microstructure and properties of graphite nanoflakes/Cu matrix composites fabricated by pressureless sintering and subsequent thermo-mechanical treatment

Effects of Graphite Contents on the Microstructure Evolution, Mechanical Properties and High Temperature Tribological Behavior of Cu–Ni–Al/Gr Solid-Lubricating Composites

Effect of sintering temperature on microstructure and tribological properties of copper/graphite composites doped with Ti3AlC2 particles

Fast Fabrication of In-Situ Micro-Nano Al_2O_3 Reinforced Fe-Cr-Ni Composites by Hot-Pressing at Low Temperature

Effect of graphene on microstructure and properties of Gr/CuCr10 composites

Synergistic enhancing effect of tungsten-copper coated graphite flakes and aluminum nitride nanoparticles on microstructure, mechanical and thermal properties of copper matrix composites

Improvement of Interfacial Bonding and Mechanical Properties of Cu-Al2o3 Composite by Cr-Nanoparticle-Induced Interfacial Modification

Microstructural evolution and mechanical property of Cu‐Cr‐Zr‐ZrB2 composites subjected to cryorolling and aging treatment