Abstract:In recent years, the addition of Ni has been widely acknowledged to be capable of enhancing the mechanical properties of Al-Si alloys. However, the effect of Ni on the wear behaviors of Al-Si alloys and Al matrix composites, particularly at elevated temperatures, remains an understudied area. In this study, Al-Si-Cu-Mg-Ni/20wt% SiC particles (SiCp) composites with varying Ni contents were prepared by using a semisolid stir casting method. The effect of Ni content on the dry sliding wear behavior of the prepared composites was investigated through sliding tests at 25 and 350°C. Results indicated that the θ-Al 2 Cu phase gradually diminished and eventually disappeared as the Ni content increased from 0wt% to 3wt%. This change was accompanied by the formation and increase in δ-Al 3 CuNi and ε-Al 3 Ni phases in microstructures. The hardness and ultimate tensile strength of the as-cast composites improved, and the wear rates of the composites decreased from 5.29 × 10 −4 to 1.94 × 10 −4 mm 3 /(N·m) at 25°C and from 20.2 × 10 −4 to 7 × 10 −4 mm 3 /(N·m) at 350°C with the increase in Ni content from 0wt% to 2wt%. The enhancement in performance was due to the presence of strengthening network structures and additional Ni-containing phases in the composites. However, the wear rate of the 3Ni composite was approximately two times higher than that of the 2Ni composite due to the fracture and debonding of the ε-Al 3 Ni phase. Abrasive wear, delamination wear, and oxidation wear were the predominant wear mechanisms of the investigated composites at 25°C, whereas delamination wear and oxidation wear were dominant during sliding at 350°C.

Influence of Ni content on the microstructure and mechanical properties of chromium carbide-nickel composites

Influences of Ni/Cu/Cr3C2 Composite Additive on Microstructure and Properties of WC–10Co Fine Grained Hardmetal

Effects of Ni content and sintering temperature on the microstructure and mechanical properties of TiC-Ni composites fabricated by selective carburization of Ti-Ni alloys

Effect of Cr on solidification structure and microhardness of Al-Ni alloy

Interface characterization and mechanical properties of Mo-added chromium carbide-nickel composite

Mechanical Behaviors of Chromium- or Niobium-Modified Ni47.5Al25Fe27.5 Alloy at Elevated Temperature

In-situ hybrid Cr3C2 and γ′-Ni3(Al, Cr) strengthened Ni matrix composites: Microstructure and enhanced properties

Effect of Chromium Carbide Addition on the Microstructures and Properties in Dual Carbide Phases Reinforced Ni-Based Composite Coatings by Plasma Cladding

Effect of Ni Content on Microstructure, Mechanical Properties, and Abrasion Behavior of Fe-B-C Alloy

Microstructure and High-Temperature Mechanical Properties of CrMnFeCoNi/TiAl Composites Prepared by Powder Metallurgy

Ni composites reinforced with ultrafine and uniform TiCx and Cr3C2 particles in situ: Enhanced properties and a well-matched interface

Effect of nickel content on the sintering behavior, mechanical and dielectric properties of Al2O3/Ni composites from coated powders

Microstructure and properties of Cu-Cr-Nb/graphite composites with high softening temperature

Effects of Ni Addition on the Mechanical and Electrical Properties of Cu-15 Mass%Cr In-Situ Composites

Effect of Ni content on the wear behavior of Al-Si-Cu-Mg-Ni/SiC particles composites

Effect of Nb addition on microstructure and mechanical properties of TiC/Ti-7.8Cr composites

Effect of (nbti)c Particles on the Microstructure and Hardness of High Chromium and Nickel Indefinite Chilled Cast Iron

Microstructures and mechanical properties of in-situ FeCrNiCu high entropy alloy matrix composites reinforced with NbC particles

Effects of in situ composite ceramics on the mechanical properties and microstructure of Fe–Cr–Ni alloys

Effect of Cr Contents on Microstructure and Mechanical Properties of ( TiBw + TiCp)/(Ti-4.0Fe-7.3Mo-xCr) Composites

Effect of Ni Content on Microstructure and Properties of WC-Ni Composites Prepared by Electroless Plating and Powder Metallurgy