Abstract:Highlights • Hot-rolled Mg-3Al-0.5Ce alloy showed anisotropic compressive behavior majorly due to basal texture. • Presence of Al 11 Ce 3 precipitates reduced the basal texture intensity, reducing the stage-II strain hardening. • Sigmoidal flow behavior ∥ to rolling (RD) & transverse direction (TD) due to extension twinning induced geometric hardening. • Parabolic flow behavior ∥ to normal direction (ND) due to slip-based deformation and no twinning. • Long-aligned Al 11 Ce 3 precipitates present within the elongated grain boundaries along RD delay the ET nucleation events. This work investigates the anisotropic compressive deformation of hot-rolled Mg-3Al-0.5Ce alloy and correlates it with microstructure and texture. Hot-rolled alloy had elongated and equiaxed grains with long-aligned Al 11 Ce 3 precipitates within the grain boundaries along rolling direction (RD) and basal texture along normal direction (ND). Analytical and crystal plasticity-based viscoplastic self-consistent predominant twin reorientation (VPSC-PTR) approaches were employed to simulate the flow curve and texture evolution for deeper insight into the deformation behavior. For compression direction (CD)∥to RD and transverse direction (TD), the basal texture was ∼⊥ to CD, which favored {101 ̄2}〈101 ̄1〉 extension twins (ET). The ETs nucleate, broaden and engulf the parent matrices with strain, rotating the lattice by ∼86.4∘ about 〈21 ̄1 ̄0〉 axes to a geometrically hard orientation with c-axis ∼∥toCD , leading to sigmoidal flow and increasing stage-II strain hardening rate (SHR). However, Al 11 Ce 3 weakened the basal texture intensity, reducing the stage-II strain hardening compared to the single-phase Mg alloy investigated earlier. The presence of Al 11 Ce 3 intermetallics delayed the ET nucleation event, which initiates at ε∼0.018 . The ET fraction evolves to ∼0.85 , lower than in the previous works on single phase Mg alloy. A reduction in the +ve SHR slope could be observed from ε = 0.03 to 0.06, indicating increased slip activities in this portion of stage-II. Beyond ε = 0.1, decreasing stage-III SHR was observed due to basal 〈 a 〉, and pyr 〈 c + a 〉- I and II slip activities in the ET orientation. The difference in the compressive behavior along RD and TD could not be observed due to Al 11 Ce 3 precipitate's morphology with elongation along RD. For CD∥to ND, the compressive flow behavior was parabolic with decreasing SHR due to slip-based deformation. ET didn't form, and the texture change was negligible, with initial and final textures having basal texture ∼∥toCD , the geometrically hard orientation. Graphical abstract Download: Download high-res image (511KB) Download: Download full-size image

Twin recrystallization mechanisms in magnesium-rare earth alloys

Texture tailoring and microstructure refinement induced by {11−21} and {10−12} twinning in an extruded Mg-Gd alloy

Twin recrystallization mechanisms in a high strain rate compressed Mg-Zn alloy

Anisotropic compressive deformation behavior of hot-rolled Mg-3Al-0.5Ce alloy

Quantitative investigation on the {10–12} twinning-detwinning behavior and twinning transfer of an extruded Mg-2.8Y sheet during compression-tension loading via quasi-in-situ EBSD observation

On the Plasticity and Deformation Mechanisms in Magnesium Crystals

On the role of selective nucleation and growth to recrystallization texture development in a Mg-Gd-Zn alloy

Microtexture Evolution Via Deformation Twinning and Slip During Compression of Magnesium Alloy AZ31

Evolution of deformation mechanisms and their orientation dependence in fine-grained Mg-3Gd during tension

The synergistic and interactive effects of slip systems and dynamic recrystallization on the weakening basal texture of Mg-Y-Nd-Zr-Gd magnesium alloy

The Effect of Tension Twin on the Dynamic Recrystallization Behavior in Polycrystal Magnesium by Atomistic Simulation

Twinning–Detwinning-Dominated Cyclic Deformation Behavior of a High-Strength Mg-Al-Sn-Zn Alloy during Loading Reversals: Experiment and Modeling

Texture weakening effect from { 10 1 ̅ 1 } twins induced static recrystallization in ambient extrusion AZ31 magnesium alloy

A quantitative study on mechanical behavior of Mg alloys with bimodal texture components

Dynamic recrystallization and twinning behavior of magnesium alloy during hot tension

Response of Magnesium Microcrystals to C-Axis Compression and Contraction Loadings at Low and High Strain Rates

Microstructure Evolution and Selection Behavior of Twin Variants of Mg-5Gd-3Y-0.5Zr Alloy during Secondary Deformation

EBSD Analysis and Theoretical Prediction of Twin Orientations During Compression in Mg-3Al-1Zn

{ 10 1 ̄ 2 } twin–twin intersection-induced lattice rotation and dynamic recrystallization in Mg–6Al–3Sn–2Zn alloy

In Situ Monitoring of Dislocation, Twinning, and Detwinning Modes in an Extruded Magnesium Alloy under Cyclic Loading Conditions

Influence of grain size on twinning behavior of WE43 magnesium alloy during room-temperature compression deformation