Abstract:Using Atomsk and LAMMPS to construct nine bicrystal Mg models with preset voids and symmetric tilt grain boundaries, tensile simulations were performed at the same rate. The results showed that as the symmetric tilt grain boundary angle increased from 20° to 30°, the yield stress decreased from 2.28 to 1.42 GPa. Based on the plastic deformation and stress–strain curves, the nine bicrystal magnesium models with different symmetric tilt grain boundaries can be divided into two groups: the first group ranges from 20° to 40°, and the second group from 45° to 80°. A representative case is selected from each group. In the first group of models, the main modes of plastic deformation are grain boundary migration, basal dislocation slip, and stacking faults; whereas in the second group, there is a higher number of basal dislocation slips, leading to a greater quantity of stacking faults, and thus a stronger capacity for plastic deformation.2 A twin‐crystal magnesium (Mg) model with 9 different symmetric tilt grain boundary (STGB) angles (20°–80°) with preset nanohole defects is established by atomsk and lammps software. The mechanical behavior of grain boundary (GB) angles on twin‐crystal Mg with cavity defects and its cavity evolution are simulated by the molecular dynamics method with embedded atomic potential, and the plastic deformation mechanism is revealed. The results show that the yield stress decreases with the increase of the STGB Angle during the stretching process. When the GB Angle increases from 20° to 80°, the yield stress decreases from 2.28 to 1.42 Gpa. This is because the larger the STGB Angle is, the larger the Schmidt factor is, and the easier it is to start dislocation slip during the stretching process. On the other hand, the larger the Angle of STGB, the more the number of atomic voids at the interface, and the more the number of dislocation nucleation points. The larger the Angle of STGB, the lower the strength of twinning Mg but the better the plasticity to avoid fracture. The plastic deformation mechanism mainly includes the nucleation of Shockley incomplete dislocation at STGBs, dislocation slip generates stacking faults (SFs), GB migration, and base plane dislocations.

The Effect of Tension Twin on the Dynamic Recrystallization Behavior in Polycrystal Magnesium by Atomistic Simulation

Crystal plasticity-based finite element modeling of twin transmission across grain boundaries in magnesium

Study on the Twinning/De-twining Behavior of Different Types of Twin–Twin Interaction via Experiments and Molecular Dynamics Simulation

Towards understanding double extension twinning behaviors in magnesium alloy during uniaxial tension deformation

Atomistic Simulation on the Twin Boundary Migration in Mg under Shear Deformation

Energetic contributions to deformation twinning in magnesium

Effects of deformation twins on microstructure evolution, mechanical properties and corrosion behaviors in magnesium alloys - A review

{ 10 1 ̄ 2 } twin–twin intersection-induced lattice rotation and dynamic recrystallization in Mg–6Al–3Sn–2Zn alloy

Twin-solute, twin-dislocation and twin-twin interactions in magnesium

Three-dimensional study of grain scale tensile twinning activity in magnesium: A combination of microstructure characterization and mechanical modeling

On the interaction of precipitates and tensile twins in magnesium alloys

Twin recrystallization mechanisms in a high strain rate compressed Mg-Zn alloy

Plastic deformation of magnesium single crystal: a crystal plasticity coupled twinning phase field simulation

Effects of texture and twinning on the torsional behavior of magnesium alloy solid rod: A crystal plasticity approach in comparison with uniaxial tension/compression

Crystal plasticity finite element modeling of twin band formation and evolution together with the macroscale mechanical responses of hexagonal metals

Effect of pre-deformation on the activation stress of {10–12} twinning in Mg–3Al–1Zn alloy

Effects of {10-12} Twin Boundary on Nanotribological Behavior of Pure Mg: A Molecular Dynamics Simulation

Quantitative investigation on the {10–12} twinning-detwinning behavior and twinning transfer of an extruded Mg-2.8Y sheet during compression-tension loading via quasi-in-situ EBSD observation

Study on the Plastic Deformation Mechanism of Void‐Containing Twin‐Crystal Magnesium with Symmetric Tilt Grain Boundary Angles

The Effect of Twins on Mechanical Properties and Microstructural Evolution in AZ31 Magnesium Alloy during High Speed Impact Loading

Plastic deformation response during crack propagation in Mg bicrystals with twin boundaries