Abstract:In-plane uniaxial tension of AZ31 magnesium alloy sheet with non-basal texture has been conducted in order to demonstrate the effects of loading direction on the microstructure evolution and mechanical properties at ambient temperature. Loading axes are chosen to be along five directions distributed between rolling direction (RD) and transverse direction (TD), allowing various activities in involved slip and twinning modes to take place. As for twinning modes, electron backscattered diffraction observations confirm that the contribution of \({{\{ 10\overline{1}1\} }}\) compression twinning is minimal to the plastic deformation of all deformed samples. By comparison, \({{\{ 10\overline{1}2\} }}\) extension twinning (ET) not only serves as an important carrier on sustaining and accommodating plastic strain but also contributes to the emergence of TD-component texture with the progression of plastic strain. In terms of slip modes, analysis on Schmid factor demonstrates that the increasing tilted angle between loading direction and RD of sheet is unfavorable to the activation of basal <a> slip, whereas it contributes to the activation of prismatic <a> slip. These observations consequently explain the increasing tendency of 0.2% proof yield stress. Moreover, the activations of basal <a> slip and \({{\{ 10\overline{1}2\} }}\) ET collectively contribute to the concentration of two tilted basal poles toward normal direction. With increasing angle between loading direction and RD, the activations of basal <a> slip and \({{\{ 10\overline{1}2\} }}\) ET are gradually weakened. This leads to a weakening tendency about concentration of two tilted basal poles, a generally increasing tendency about Lankford value (r-value) and a generally decreasing tendency about strain-hardening exponent (n-value).

Microtexture Evolution Via Deformation Twinning and Slip During Compression of Magnesium Alloy AZ31

Microstructure Evolution of AZ91D Magnesium Alloy During High Temperature Compression

Research on deformation mechanism of AZ31 magnesium alloy during uniaxial compression

Microstructure Evolution and Mechanical Behavior of AZ31 Magnesium Alloy Sheet with Bimodal Texture under Bending Deformation

Effect of crystal orientation on the deformation behavior of the magnesium alloy AZ31 during plane strain compression

Effect of texture types on microstructure evolution and mechanical properties of AZ31 magnesium alloy undergoing uniaxial tension deformation at room temperature

Anisotropic Deformation of Extruded Magnesium Alloy AZ31 under Uniaxial Compression: A Study with Simultaneous in Situ Synchrotron X-Ray Imaging and Diffraction

Influence of Grain Orientation on Twinning During Warm Compression of Wrought Mg–3Al–1Zn

Effect of Temperature on Microstructure and Texture During Compression of Az31

Effect of deformation conditions on twinning of AZ31 magnesium alloy during compression test

Dependence of Microstructure Evolution and Mechanical Properties on Loading Direction for AZ31 Magnesium Alloy Sheet with Non-basal Texture During In-Plane Uniaxial Tension

Hot Deformation Behavior and Microstructural Evolution of Twin-Roll-Casting Mg Alloy during High-Temperature Compression

Microstructure and Texture Evolution of Mg-3Zn-1Al Magnesium Alloy During Large-Strain Electroplastic Rolling

Multiscale Measurements on Temperature-Dependent Deformation of A Textured Magnesium Alloy with Synchrotron X-Ray Imaging and Diffraction

Mechanism of Plastic Deformation of As-Extruded AZ31 Mg Alloy during Uniaxial Compression

Microscopic mechanism exploration and constitutive equation construction for compression characteristics of AZ31-TD magnesium alloy at high strain rate

In-situ Analysis of Microscopic Plastic and Failure Behaviors of Extruded Magnesium Alloy

Influence of Local Strain on Twinning Behavior During Compression of AZ31 Magnesium Alloy

Microstructure evolution and characterization of the adiabatic shear bands in AZ31 magnesium alloy

Microstructure evolution of AZ80 magnesium alloy in semi-solid compression by molecular dynamics simulation

Extension Twin Variant Selection During Uniaxial Compression of A Magnesium Alloy