Abstract:Highlights • Hot-rolled Mg-3Al-0.5Ce alloy showed anisotropic compressive behavior majorly due to basal texture. • Presence of Al 11 Ce 3 precipitates reduced the basal texture intensity, reducing the stage-II strain hardening. • Sigmoidal flow behavior ∥ to rolling (RD) & transverse direction (TD) due to extension twinning induced geometric hardening. • Parabolic flow behavior ∥ to normal direction (ND) due to slip-based deformation and no twinning. • Long-aligned Al 11 Ce 3 precipitates present within the elongated grain boundaries along RD delay the ET nucleation events. This work investigates the anisotropic compressive deformation of hot-rolled Mg-3Al-0.5Ce alloy and correlates it with microstructure and texture. Hot-rolled alloy had elongated and equiaxed grains with long-aligned Al 11 Ce 3 precipitates within the grain boundaries along rolling direction (RD) and basal texture along normal direction (ND). Analytical and crystal plasticity-based viscoplastic self-consistent predominant twin reorientation (VPSC-PTR) approaches were employed to simulate the flow curve and texture evolution for deeper insight into the deformation behavior. For compression direction (CD)∥to RD and transverse direction (TD), the basal texture was ∼⊥ to CD, which favored {101 ̄2}〈101 ̄1〉 extension twins (ET). The ETs nucleate, broaden and engulf the parent matrices with strain, rotating the lattice by ∼86.4∘ about 〈21 ̄1 ̄0〉 axes to a geometrically hard orientation with c-axis ∼∥toCD , leading to sigmoidal flow and increasing stage-II strain hardening rate (SHR). However, Al 11 Ce 3 weakened the basal texture intensity, reducing the stage-II strain hardening compared to the single-phase Mg alloy investigated earlier. The presence of Al 11 Ce 3 intermetallics delayed the ET nucleation event, which initiates at ε∼0.018 . The ET fraction evolves to ∼0.85 , lower than in the previous works on single phase Mg alloy. A reduction in the +ve SHR slope could be observed from ε = 0.03 to 0.06, indicating increased slip activities in this portion of stage-II. Beyond ε = 0.1, decreasing stage-III SHR was observed due to basal 〈 a 〉, and pyr 〈 c + a 〉- I and II slip activities in the ET orientation. The difference in the compressive behavior along RD and TD could not be observed due to Al 11 Ce 3 precipitate's morphology with elongation along RD. For CD∥to ND, the compressive flow behavior was parabolic with decreasing SHR due to slip-based deformation. ET didn't form, and the texture change was negligible, with initial and final textures having basal texture ∼∥toCD , the geometrically hard orientation. Graphical abstract Download: Download high-res image (511KB) Download: Download full-size image

Anisotropic compressive deformation behavior of hot-rolled Mg-3Al-0.5Ce alloy

Study on the low mechanical anisotropy of extruded Mg-Zn-Mn-Ce-Ca alloy tube in the compression process

Understanding the mechanisms of texture evolution in an Mg-2Zn-1Ca alloy during cold rolling and annealing

Insights into the evolution of texture and mechanical properties during warm rolling and annealing of Mg–2Zn-0.5Ca alloy

Microstructure evolution and mechanical property of Mg-3Al alloys with addition of Ca and Gd during rolling and annealing process

Effect of cerium alloying on microstructure, texture and mechanical properties of magnesium during cold-rolling process

Twin recrystallization mechanisms in magnesium-rare earth alloys

Effect of Al addition and rolling reduction on microstructure and texture evolution of Mg–3Sn alloy during high-speed rolling

Anisotropic cyclic deformation behavior of an extruded Mg-3Y alloy sheet with rare earth texture

Non-Basal Slip Induced Rare Earth Texture Evolution in Mg-14Gd-0.5Zr (wt.%) Alloy During the Traditional Hot Rolling

The microstructure evolution and mechanical anisotropy of extruded Mg-2Zn-0.4Ce-0.4Mn alloy tube during tension in different directions

Effect of texture types on microstructure evolution and mechanical properties of AZ31 magnesium alloy undergoing uniaxial tension deformation at room temperature

Hot deformation behavior of novel high-strength Mg-0.6Mn-0.5Al-0.5Zn-0.4Ca alloy

Unveiling the Rolling Texture Variations of Α-Mg Phases in a Dual-Phase Mg-Li Alloy

Strength Differential Effect and Anisotropy of Mg–1.9Mn–0.3Ce (Wt-%) Alloy Subjected to High-Rate Loadings

Utilizing integrated neutron diffraction and elastoplastic self-consistent crystal plasticity model to quantitatively assess the strengthening mechanism in Al-12.5Ce and Al-12.5Ce-0.4Mg alloys

Effect of Al Concentration on Basal Texture Formation Behavior of AZ-Series Magnesium Alloys during High-Temperature Deformation

Revealing the deformation behavior and microstructure evolution in Mg-12Y–1Al alloy during hot compression

Rolling texture development in a dual-phase Mg-Li alloy: The role of temperature

High corrosion resistance and weak corrosion anisotropy of an as-rolled Mg-3Al-1Zn (in wt.%) alloy with strong crystallographic texture

Effect of rolling temperature on microstructure and mechanical properties of hot-rolled Mg-Al-Ca-Zn-Mn alloys