Abstract:Center segregation and banded intergranular segregation (B-IGS) should be well controlled to improve the mechanical properties of twin-roll cast (TRC) aluminum alloys, especially for alloys with high solidification intervals. In the present work, a synergistic grain refinement strategy was designed using an Al-5Ti-B grain refiner and Ti, Zr, and Sc microalloying elements to simultaneously control center segregation and B-IGS in TRC Al-Zn-Mg-Cu alloys. As the grain size decreased, center segregation defects were eliminated and transformed into dispersed B-IGS defects; simultaneously, the width and length of the B-IGS were also reduced. Moreover, the macro-distributions of the alloying elements along the thickness direction became more homogeneous due to a weak shear-induced dilation effect. The well-controlled multiscale segregation improved the uniformity of the alloy macrostructure, accelerated the redissolution of the crystalline phase, dispersed the aggregated residual phase, and refined grains under the T6 state. Hence, the strength and ductility of the alloys under the T6 state were simultaneously improved, and the hardness distribution along the thickness direction became more homogenous. Furthermore, the underlying mechanisms of segregation evolution and strength and ductility enhancements were elucidated. This work provides a novel strategy to effectively control multiscale segregation and produce high-performance aluminum alloys with high solidification intervals by TRC.

Mitigating segregation and synergistically improving corrosion resistance via Ca-Y microalloying in twin-roll cast Mg-Al-Mn dilute alloys

Enhancing corrosion resistance of Mg-Al-Mn-Ca-Y dilute alloy via novel core-shell structured Al8Mn4Y-Al2Ca and controllable solute segregation

Role of alloyed Al on the microstructure and corrosion behavior of as-cast dilute Mg-2Zn- x Al-0.5Ca alloys

Effect of minor Ca addition on microstructure and corrosion behavior of Mg–Y–Ca alloys

Effects of micro-alloying Ag on microstructure, mechanical properties and corrosion behavior of extruded Mg-2Zn-0.2Ca-xAg alloys

Improvement of Mechanical Properties and Corrosion Resistance of As‐Extruded Mg–2Zn–2Al–0.3Mn Alloy Through Y Addition

Microstructure, mechanical properties and corrosion behavior of extruded Mg-Zn-Ca alloys with same Zn/Ca atomic ratio

Influence of mixed rare earth elements(Y and Ce) on the microstructure and corrosion behaviour of Mg-4Al-3Ca alloy

Tailoring the corrosion behavior and mechanism of Mg-Gd-Zn alloys via Sc microalloying

Effect of Al/Mn ratio on corrosion behavior of lean Mg-Zn-Ca-Al-Mn alloy processed by twin-roll casting

Enhancing Strength-Ductility Synergy and Corrosion Residual Strength of Hot-Rolled Mg-2Zn-0.85Y Alloy

Effect of Mo on Segregation Behavior of Al-Mg-Si-Mn Alloy Produced by Twin-Roll Casting

Tailoring the microstructure and enhancing the corrosion resistance of extruded dilute Mg-0.6Al-0.5Mn-0.25Ca alloy by adding trace Ce

Intercalation of Y in Mg-Al layered double hydroxide films on anodized AZ31 and Mg-Y alloys to influence corrosion protective performance

Microscopic mechanism of mechanical property improvement of the casted Al-7Si-0.4Mg-0.3Y alloy

Strength and ductility enhancement of twin-roll cast Al-Zn-Mg-Cu alloys with high solidification intervals through a synergistic segregation-controlling strategy

Effect of Microstructure on the Corrosion Behavior of as-cast and Extruded Mg–Sn–Y Alloys

Microstructure Characteristics and Corrosion Behaviors of Mg-2Zn-2Er-0.3Zr-0.3Mn Alloy under Various Rolling Reductions

In Vitro Corrosion of Mg–1.21Li–1.12Ca–1Y Alloy

Regulating corrosion resistance of Mg alloys via promoting precipitation with trace Zr alloying

Microstructure and corrosion behavior of as-homogenized and as-extruded Mg−xLi−3Al−2Zn−0.5Y alloys (x=4, 8, 12)