Abstract:Enhancing the strength of magnesium alloys by precise control of microstructure through elemental composition adjustment is a well-established strategy. In this investigation, novel Mg-5Al-8Sn-1Sr-xCa alloys were fabricated using a die-casting process, where varying amounts of calcium were incorporated to achieve a finely tuned grain size. Our comprehensive analysis, encompassing microstructural examinations and electrochemical studies, reveals that the introduction of calcium contributed to increase in remarkably resistant corrosion properties to the Mg alloy. This is particularly evident in an acceptable decomposition rate under conditions simulating chloride ion concentration found in the human body. The alloy with added calcium showcases a lower corrosion current, elevated polarization resistance, and the uniform formation of mixed oxides/hydroxides distributed across the alloy surface. These outcomes signify substantial improvements in corrosion resistance due to the reduction of α-Mg grain sizes, continuous precipitates at grain boundaries, and the formation of barrier layer on the alloy surface. This study not only advances our understanding of alloy microstructure manipulation but also provides a promising avenue for the development of cost-effective biomaterials and engineering alloys. Crucially, this approach addresses the persistent issue of rapid corrosion, strengthens loss observed in multiphase Mg alloys, and underscores the potential to overcome challenges in material design for practical applications.

Role of alloyed Al on the microstructure and corrosion behavior of as-cast dilute Mg-2Zn- x Al-0.5Ca alloys

Role of Alloyed Al on the Microstructure and Corrosion Behavior of As-Cast Dilute Mg-2Zn-xAl-0.5Ca Alloys

Influence of Ca Addition on Microstructure, Mechanical Properties and Corrosion Behavior of Mg-2Zn Alloy

Microstructure, Mechanical, and Corrosion Properties of Extruded Low-Alloyed Mg-xZn-0.2Ca Alloys

Effect of Ca Addition on the Corrosion Behavior of Mg–Al–Mn Alloy

Effect of Al Content on the Corrosion Behavior of Extruded Dilute Mg–Al–Ca–Mn Alloy

Effect of Grain Size and Volume Fraction of Eutectic Structure on Mechanical Properties and Corrosion Behavior of As-Cast Zn–Mg Binary Alloys

Effects of micro-alloying Ag on microstructure, mechanical properties and corrosion behavior of extruded Mg-2Zn-0.2Ca-xAg alloys

Microstructure and Corrosion Behavior of the As-cast Mg-xAl (x=9%, 12%, 15%) Alloys

The effects of Ca on the microstructure, mechanical and corrosion properties of extruded Mg-2Zn-0.5Mn alloy

Microstructure-corrosion Behaviour Relationship of Micro-Alloyed Mg-0.5Zn Alloy with the Addition of Ca, Sr, Ag, in and Cu

Effect of Sn Addition on the Microstructure and Corrosion Behavior of Dilute Wrought Mg-Zn-Ca Series Alloys

Effect of Alloying Elements on Corrosion Behaviour of Binary Magnesium Alloys

Effects of Cooling Rate on Microstructure, Mechanical and Corrosion Properties of Mg–Zn–Ca Alloy

Investigating the corrosion behavior of as‐cast Mg‐Zn‐Ca alloys with the same Zn/Ca atomic ratio by in situ observation

Microstructure and corrosion behavior of as-homogenized and as-extruded Mg−xLi−3Al−2Zn−0.5Y alloys (x=4, 8, 12)

Microstructure and Corrosion Behavior of As-Homogenized Mg-xLi-3Al-2Zn-0.2Zr Alloys (x=5, 8, 11 Wt%)

Effect of Al/Mn ratio on corrosion behavior of lean Mg-Zn-Ca-Al-Mn alloy processed by twin-roll casting

Effect of Ca Micro-Alloying on the Microstructure and Anti-Corrosion Property of Mg0.5Zn0.2Ge Alloy

An Investigation on the Improved Corrosion Resistance of Die Casting Mg-5Al-8Sn-1Sr-xCa Alloys

Microstructure, mechanical properties and corrosion behavior of extruded Mg-Zn-Ca alloys with same Zn/Ca atomic ratio