Abstract:In this paper, mechanical properties and microstructures of the cast and extruded Al-xCu-1Li-0.4Mg–1Zn-0.1Zr alloys (x = 2.0, 3.0, 4.0, 4.5, 5.5, 6.5 wt%) were investigated. The results showed that the as-cast micrographs of alloys with different Cu content primarily consist of dendritic α-Al grains, and the intermetallic phases at the grain boundaries were Cu and Zr rich phases. After solution treatment, no recrystallization took place in extruded alloys, and the alloys mainly represented mixed textures composed of <111> and <100> fibers. Cu significantly affected the precipitation behavior of the extruded alloys. Only T1 (Al2CuLi) phases were observed in T6 (aging at 175 °C for 32 h) and T8 (3% pre-strain followed by aging at 150 °C for 32 h) treated alloy with 2 wt% Cu. Further increasing Cu contents (4.5 and 6.5 wt%) enabled the co-precipitation of T1 and θ' (Al2Cu) phases, as well as increased their density. In addition, the microstructures of grain boundaries of alloys with different Cu content showed dramatic differences. T1 phases precipitated at the grain boundaries of alloy containing 2 wt% Cu, while rare precipitation of T1 phases was observed at the grain boundaries of alloy with 6.5 wt% Cu. The yield strength (YS) of the alloys increased with the Cu content and the elongation (EL) showed an opposite trend. A good combination of ultra-high strength (YS = 684 MPa, ultimate tensile strength = 726 MPa) and ductility (EL = 6.3%) was obtained in T8 treated alloy containing 4.5 wt% Cu. The presence of the undesired coarse T2 (Al6CuLi3) phases at the grain boundaries resulted in the premature failure of the high Cu content alloys.

Microstructure, Mechanical Properties, and Corrosion Behavior of Al-4.0Cu-1.1Li-0.5Mg-xAg Alloys

Microstructure and Mechanical Properties of Al–Cu–Mg–Mn–Zr Alloy with Trace Amounts of Ag

Microstructure, Mechanical Properties and Corrosion Behaviors of Al–Li–Cu–Mg–Ag–Zn Alloys

Effect of Aging Time on the Microstructural Characterization and Corrosion Resistance of Al-4.5Cu-1Li-0.4Mg-0.4Ag-0.4Mn-0.5Zn Alloys

Effect of Cu Content on Microstructure and Mechanical Properties of Al-Cn-0.4Mg-0.6Ag Alloy

Effects of micro-alloying Ag on microstructure, mechanical properties and corrosion behavior of extruded Mg-2Zn-0.2Ca-xAg alloys

Microstructure of Al-5Cu-1Li-0.6Mg-0.5Ag-0.5Mn Alloys

Effect of Mg Content on Mechanical Properties and Microstructure of Al-4.8Cu-xMg-1.0Ag Alloys

Influence of Mg Content on the Corrosion Behavior and Precipitation of Aged Al-Cu-Li-xMg Alloys

Role of Cu on the Mechanical Properties and Microstructures Evolution of Al-xCu-1Li-0.4Mg–1Zn-0.1Zr Alloys

Effects of Ag, Mg Micro-Alloying on Aging Characteristics and Microstructure of Al-Cu-Li Alloy

Microstructure and Mechanical Properties of Mg, Ag and Zn Multi-Microalloyed Al–(3.2–3.8)Cu–(1.0–1.4)Li Alloys

Research on Precipitation and Mechanical Properties of Al-Cu-0.4Mg-0.6Ag Alloy

Ageing characteristics and microstructure of Al-4Mg-1. 5Cu alloys containing silver and lithium

Microstructures and Mechanical Properties of Al-Cu-Mg-(Ag, La) Alloys

Effect of minor Ag addition on microstructures and properties of Al-Mg-Cu-Li alloy with low Cu/Mg ratio

Precipitate microstructures, mechanical properties and corrosion resistance of Al-1.0 wt%Cu-2.5 wt%Li alloys with different micro-alloyed elements addition

Microstructure and corrosion behavior of as-homogenized and as-extruded Mg−xLi−3Al−2Zn−0.5Y alloys (x=4, 8, 12)

Influence of Ag on microstructure, mechanical properties and tribological properties of as-cast Al-33Zn-2Cu high-zinc aluminum alloy

Effects of Cu and Mg Contents on Mechanical Properties of Al-xCu-yMg-0.6Ag Alloy

Microstructure and Mechanical Properties of Cast Al-Li-Mg Alloy: Role of Cu Addition and Heat Treatment