Abstract:This study investigated the effect of adding La–Ce mixed rare earths and Sr on the microstructure and mechanical properties of AlSi10MnMg alloy. The experiment utilized different combinations of modifiers, including single La–Ce rare earths, single Sr, and the combined addition of La–Ce mixed rare earths and Sr. This study compared their effects on grain refinement, the modification of the α-Al phase and eutectic silicon phase, and tensile properties and hardness. The results showed that the combined modification of Sr and mixed rare earth elements significantly refined the grains, optimized the morphology of the α-Al phase and eutectic silicon phase, and improved the overall mechanical properties of the aluminum alloy. Under the combined modification, the addition of 0.02 wt.% Sr and 0.1 wt.% RE (La–Ce mixed rare earths) exhibited the most pronounced refining effect. The secondary dendrite arm spacing (SDAS) was reduced by 59.18%. The eutectic silicon phase transformed from coarse needle-like shapes to fine fibrous or granular forms, with an aspect ratio reduction of 69.39%. Meanwhile, the alloy's tensile strength and hardness were significantly improved. The tensile strength increased to 240 MPa, achieving an increase of 23.08%; the yield strength increased to 111 MPa, achieving an increase of 18.09%; and the elongation reached 7.3%, achieving an increase of 73.81%. This indicates that the proper addition of Sr and mixed rare earths can significantly optimize the microstructure and enhance the mechanical properties of AlSi10MnMg alloy, providing an effective method for the preparation of high-performance heat-treatment-free aluminum alloys.

Influence of mixed rare earth elements(Y and Ce) on the microstructure and corrosion behaviour of Mg-4Al-3Ca alloy

Tailoring the microstructure and enhancing the corrosion resistance of extruded dilute Mg-0.6Al-0.5Mn-0.25Ca alloy by adding trace Ce

EFFECT OF CERIUM AND LANTHANUM ALLOYING ON MICROSTRUCTURE AND CORROSION BEHAVIOR OF AZ91 MAGNESIUM ALLOY

Enhanced Mechanical Properties and Corrosion Resistance of Rolled Mg-1.5Sn-0.5Ca Alloy by Ce Microalloying

Influence of Rare Earth Element (Y) on Microstructure and Corrosion Behavior of Hot Extrusion AZ91 Magnesium Alloy

Effect of Ce and Y on Microstructures and Properties of Al-11.0Zn-3.1Mg-1.22Cu-0.1Sr-0.2Zr-0.1Ti Alloy

Study of the microstructure and mechanical properties of Mg-rare earth alloys

Effect of adding Y and Ce on corrosion behaviour of the extruded ZK60 magnesium alloy

Effect of Y and Ce Micro-alloying on Microstructure and Hot Tearing of As-Cast Al–Cu–Mg Alloy

Effect of Rare Earth Elements (Y, La) on Microstructural Characterization and Corrosion Behavior of Ternary Mg-Y-La Alloys

Study on the Strengthening Mechanism of Rare Earth Ce in Magnesium Alloys, Based on First-Principle Calculations and Electronegativity Theory

Microstructures, Mechanical Properties and Corrosion Resistances of Extruded Mg-Zn-Ca-Xce/La Alloys

A Comparison Study of Ce/La and Ca Microalloying on the Bio-Corrosion Behaviors of Extruded Mg-Zn Alloys

Microstructural homogeneity, texture and corrosion properties of RE-doped 55Mg-35Pb-9.2Al-0.8B alloy fabricated via equal channel angular pressing (ECAP)

Effect of Rare Earth Element Ce and La on Corrosion Behavior of AM60 Magnesium Alloy

Microstructure and Mechanical Properties of Mg-Xy-1.5mm-0.4zr Alloys

The microstructural characterization and wear behavior of Mg-Zn-Ce alloy with trace Ca addition

In Vitro Corrosion of Mg–1.21Li–1.12Ca–1Y Alloy

Microstructure and corrosion properties of Mg–0.5Zn–0.2Ca–0.2Ce alloy with different processing conditions

The effects of substitution of yttrium for Ce-rich mischmetal on the mechanical properties and thermal conductivity of mg–4Al–4Zn–4RE alloy

The Influence of the Combined Addition of La–Ce Mixed Rare Earths and Sr on the Microstructure and Mechanical Properties of AlSi10MnMg Alloy